Answer / bariumesh8

proportional to Surface energy of the material.

Answer / rajesh

power required for crushing the material mainly depends on
the product size it means surface energy of the material. so
if the product size is very fine then the power
requirement is more.

Answer / poonam

proportional to Surface energy of the material.

Answer / sourya

the power required for crushing not only depends on the
initial and final product sizes but also the type of
material whether soft or hard. That's why we have three
power law relations for crushing, kick, rittinger and bond's
law.

Answer / vinayak desai

THE POWER REQUIRED FOR CRUSHING IS DEPENDS UPON THE SIZE &
DENSITY OF THE MATERIEAL

Hi, I am Gurunathan. I am in need of ONGC, IOCL, DRDO technical test ( chemical engineering)and general aptitude questions. If anyone has kindly post it to me soon.

0 Answers   Nelco,

---

Explain what is the method involved in analyzing powders for composition?

0 Answers  

---

Explain how can you keep our seawater used for heat rejection clean before entering our heat exchangers?

0 Answers  

---

Question 77 - The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18, with their respective quantities in N units having the ratio of Na : Nb : Nc = 2 : 3 : 5. (a) Find the numerical average molecular weight of the polymer by using the formula (Ma Na + Mb Nb + Mc Nc) / (Na + Nb + Nc). (b) Find the weighted average molecular weight of the polymer by using the formula (Ma Na Ma + Mb Nb Mb + Mc Nc Mc) / (Ma Na + Mb Nb + Mc Nc). (c) Calculate the polydispersity Q by using the answer in (b) divided by answer in (a). (d) Find the volumetric average molecular weight of the polymer by using the formula (Ma Na Ma Ma + Mb Nb Mb Mb + Mc Nc Mc Mc) / (Ma Na Ma + Mb Nb Mb + Mc Nc Mc). (e) Estimate the polydispersity Q by using the answer in (d) divided by answer in (b).

1 Answers  

---

What are some common causes of control valve noise?

0 Answers  

---

---

Explain the difference between cfm (cubic feet per minute) and scfm (standard cubic feet per minute)?

0 Answers  

---

How can you prevent bridging in a dilute phase pneumatic conveying system?

0 Answers  

---

The process conditions of the fuel gas are as follows: Temperature = 25 deg C Pressure = 4 bar g Calculate the line size for the fuel gas supply line to the superheater

0 Answers  

---

What is the pattern of interview questions and which field is of high importance viz., Mass Transfer, Heat Transfer, Petroleum Refining etc ?

2 Answers   Cairn, IOCL, Reliance,

---

ENGINEERING NUMERICAL METHODS - EXAMPLE 19.1 : Solve the simultaneous equation using simple Excel program : r + s - t = 7, 2r - s = 0, 3r + 2t = 15. Explain the use of functions of MINVERSE and MMULT together with the keyboard C (Ctrl) + S (Shift) + E (Enter).

1 Answers  

---

Question 64 – According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

Question 60 – During the landing process of an airplane, the velocity is constant at v. (a) If the displacement of the plane is x at time t, find the differential equation that relates t, x and v. (b) The plane has 2 parts of wheels – the front and the back, separated by a distance L. The front part of the wheel touches the land first, that allows the straight body of the plane to form an angle T with the horizontal land. If the vertical distance between the back part of the wheel and the horizontal land is y, find the equation of y as a function of L and T. (c) Find the differential equation that relates dy as a function of dt, v and sin T. (d) Find the differential equation that consist of dy as a function of y, L, v and dt. (e) Find the equation of y as a function of v, L, t and C where C is a constant. (f) When t = 0, prove that y = exp C as the initial value of y.

1 Answers  

---