can we light the mercury vapour (tube light)with out a 1).starter and 2).choke

Categories >> Engineering >> Electrical Engineering
Suggest New Category

can we light the mercury vapour (tube light)with out a
1).starter and 2).choke in our homes if yes explain how?

Question Posted / self

5 Answers
8150 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes..

Answer / nithi

we can light the tube light without starter by using tester.
(How:disconnect the starter from the circuit,then short
&open the terminals of the circuit rapidly using tester
carefully).
BUT,
we can't light the tubelight without choke.Because it is
needed to create high voltage across terminals of the tube
light for electronic emission.

Is This Answer Correct ?

4 Yes

1 No

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes..

Answer / varun

If question is just lighting on then it can be answered as
in three steps:
1.switching on
2.instatntly Switch off
3.again switch on,
This will provide necessary high volatge across lamp
because of transient produced by choke ( a inductor)

Is This Answer Correct ?

1 Yes

0 No

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes..

Answer / smartboy123

yes phillips hpln 150W lamp is in market which is running
wihout chock and capacitor or starter.

Is This Answer Correct ?

0 Yes

0 No

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes..

Answer / smartboy123

sorry above lamp is ML lamp instead of HPLN series.

Is This Answer Correct ?

0 Yes

0 No

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes..

Answer / shyam

we can't light the mercury vapour lamp with out starter &
choke becoz to light up mercury lamp above 230v is
essential hence it is done through choke to get break the
elasticity of the atoms& to get free electrons

Is This Answer Correct ?

2 Yes

5 No

Post New Answer

More Electrical Engineering Interview Questions

in science exhibition how lamp can blink when you clap near the lamp ? thank you

0 Answers

using n1*n2 which type transformer is made; where n1 is primary turn and n2 is secondery turn

1 Answers JSW,

I COMPLITED MY B.TECH AND 10TH CLASS WITH 70%MARKS BUT 12TH CLASS 55%MARKS..CAN I GET INDIAN RAILWAY RECUREMENT EXAMINATION?

0 Answers UPSC,

I need to calculate the Battery bank back up for below configuration:- UPS - 120 KVA Battery Bank - 200Ah Volt of each cell - 12 V Total No of cell - 34 No's Can you please help me to get the battery back up time for above configuration...? along with formula

1 Answers Wipro,

What conditions are required for transformer to operate at low frequencies ?

0 Answers

i have been tasked with a design of protection, metering and control(PMC) relay panel extension to accommodate all PMC relays.There is an already existing panel where this one will be built.What are the design aspects for this kind of project? thank you.

0 Answers

What is meant by short-pitched winding?

0 Answers

What is meant by electrical speed?

1 Answers

what is full wave bridge?

4 Answers

what is the type of winding connection( star or delta) in 1HP to 5HP motors. How to check the motor winding connections( star or delta) if not provided in the nameplate?

5 Answers

what is strip power factor?

0 Answers TATA,

For 132 KV line, PT or CVT which is prefered for measuring & protection? is there any IS or IEE standard available?

1 Answers

For more Electrical Engineering Interview Questions Click Here