Answer / kingfisher

Safety Valve is for Safe operation of Machine element , for
any reason is the save value of pressure gets exceeded ,
safty valve activates to bring the system under safe
pressure levels.

Relief valve is active element in a schema of machine which
operates as a function of machine . reliving the pressure
from a pressurized or depressurized section of a circuit .

Answer / noorullah

relief valve will allow the pressure to come out
automatically when it excees where as in safety valve it is
open when it cross the exceed pressure..

Answer / mishal paul

pressure Relief valve will allow the excess pressure to come
out above certain limit and when the pressure drops valve
will automatically close.
but in case of safety valve when the pressure exceed the set
limit will release the total pressure means valve will open
until the pressure goes to zero..

Answer / york shipley

from its name it derive " the primary purpose/function of a
safety valve" is to protect the operating machine from
danger of breakdown by monitoring continuously the safe value
or set point, and function at the time of the value when
exceed the set point by actuation of its mechanism designed
to prevent the device where it is fitted by stopping.

where in the "relive valve" always meant to operate slightly
lesser than safe limits as a secondary protection device of
system which keeps the operation continued and reduce the
value of operational parameter with out stopping the device
function.

Answer / bejoy

safety valve and relief valve
the terms are used interchangeably in the industry..

some differences which i have noted in my company are..
safety valves are connected invariably to the output of a
flow creating equipment(exmple a pump or a compressor)..its
purpose is to protection frm flow restriction ahead(or any
other source of high pressure in the fluid)...
now relief valves are used everywhere where there is the
need for a pressure reduction to a set value..a sort of
pressure control valve(PCV) job can be done by a relief valve..

Answer / kashif

also one thing more b/w safety vv and relief vv safety vv
work open loop and relief vv working on close loop..

Answer / ravindran

Relife valve using to the line to avoid the damage. and
safety valve using that pressure regulation of the line.

Answer / g.s.k

safety valve is set at extreame condition ad is fixed were
as is at a set pressure and set pressure can be changedany
time

Answer / avinash

The safety valve is the value which will work both in high
pressure & low pressure situation. ( It will work irrespective
of pressures difference).
Whereas the relief valve will work only when the pressure is
high. In order to bring the required stability.

Answer / arvind yeram

function of safety valve is to indicate the operator during
low water & high pressure. but relief valve only
indicates high pressure.

What are the most immediate challenges of this position that need to be addressed in the first three months?

1 Answers   Petro Star Mount,

What is the formula for 1 HP of a two-cycle engine?

0 Answers  

How to decide the capacity of air compressor in an industry. What are the factors taken into consideration while selecting the capacity?.

1 Answers   DAE,

Iam a 2006 graduate and applying for ms degree course in USA for spring 2010.I have also received i20 from universities.I also have work experience as a cad engineer for almost 2.6 yrs. please tell me what kind of questions can be raised by US Consulate for my situation and how to answers them.

1 Answers   US Consulate,

HOW MUCHSTACK EMMISSION THROUGH YOUR CHIMNEY AND WHAT IS THE STATE GEVINORMS

1 Answers   Jindal,

when a solid shaft is subjected to tension its linear dimension changes equaly as its lateral dimension,then what will be its poissons ratio?

7 Answers   Crompton Greaves,

we use parallel flow heat exchanger to coo oil of 1000 EP viscosity,oftenly tubes may damage during cleaning etc what is proper way to clean cooler? How impurities decreased or vanished during working or in less teme job performed?

0 Answers  

What do you call the clearing of air inside cylinder after combustion?

1 Answers   RRB,

how many maximum enter 2mm Dia solid cylindrical pipe into 8mm Dia hollow cylindrical pipe. give answer with calculation.

0 Answers   Bhel,

NOW PRESENT WAHT DOING

2 Answers   Ecil,

what is over ball dimmention? why it is required? what is used in machining?

0 Answers   BEML, Greaves,

how many manhole should be there on boiler? why?

4 Answers   TATA, WBPDCL,