Interested to Buy Any Domain ? << Click Here >> for more details...
two parallel conductors are carrying the current in the same direction.which of the following statements is true? (a)there is arepelling force between the conductors (b)the force increases when the distance between the conductors is increased (c)there is an attaracting force between the conductors (d)the force increases when the distance between the conductors is decreased
1 3904In the solution of load flow eqation, Newton raphson method is superior to the gauss siedal method because (a)the time taken to perform one iteration in the NR method is less when compared to GS method (b)the number of iterations required in the NR method is more compared to that in the GS method (c)the number of iterations required is dependant on the size of the system in the NR method (d)convergence characteristics of the NR mehod are not affected by the selection of the slack bus
1 4513the transient state stability limit of a system wherin power is transmitted throgh a double transmission line is (a)equal to steady state stability limit (b)more than its steady state stability limit (c)less than than its steady state stability limit (d)equal to its dynamic stability limit
1 5820What is CRT (Contact Resistance Test) for Isolators or Dis- connector Switches? Why we performed it & whats the Testing procedure.
1 11269in one substation we have two power transformers of 100mva,75mva capacity.statoin load is155mva.how much each tranformers share the load????
6 11274what will happen if the prime mover on the field excitation of the on-coming generator fails?Explain.
5546How can calculate HT side VCB? For example I have 1250 KVA load what will be HT side VCB Amp.range and what size XLPE cable I use for HT side.
2 17049We have 250 KW x 2 motors, which are load from 25% to 100% varying load in every minute , so how can we compansate the power factor. pl give your opinions on the above subject.
18751. Design a counter which counts 0, 4, 8, 2, 6, and repeats using: 1.a using JK flip flops 1.b using T flip flops 1.c using D flip flops
1949Post New Electrical Engineering Questions
Pl.brief me any electrical major fault you have rectified.
Why generation voltage in thermal power plant is between 11kv to 33kv?
Is vtg is controlled by the resistor? if else how much?
Formulae for calculating the transmission line losses for different voltage levels
PLS MENTION QUESTIONS ASKED IN IOCL INTERVIEW FOR ELECTRICAL EGG??
An 8 pole, 50 Hz, 3-phase IM is loaded to a poing where pull out torque will occur. The rotor resistance per phase is 0.3 ohm and motor stalls at 650 rpm. The rotor reactance at stand still is A 2 ohm B 1.25 ohm C 3.15 ohm D 2.25 ohm
sir i ve applied for hindustan petroleum and power grid india ltd..and the exams on feb 22.can you pls send model papers and tell how to prepare for those.i need to get into any of these for sure.....
what is the breaking capacity and making capacity of circuit breaker and how
how many load we can take for lighting
Either the Armoured Earthing strip of HT 3 core cable have to pass through CB CT or not , why ???
1)how to reduce the value of tan delta of trasformer and CB,bushing,CT&PT,CVT ? 2)how to reduce the resistance of CB contact and its operating time? 3)plz.....send me the project report on conditioning and monitoring of substation equipment on my email id (gusaiyogendra03@gmail.com)
Differentiate between induced emf and self inductance?
If i have two 3000 kW motors and the whole facility requires a 10 MVA transformer. What would be better installing two 5 MVA transformers(one for 1 motor ) or just a single 10 MVA transformer for both of them. Give reasons for your answer.
what is differant beetween overload current and phase current?
what is the excess air in furnace
