In the solution of load flow eqation, Newton raphson method is superior to the

In the solution of load flow eqation, Newton raphson method
is superior to the gauss siedal method because
(a)the time taken to perform one iteration in the NR method
is less when compared to GS method
(b)the number of iterations required in the NR method is
more compared to that in the GS method
(c)the number of iterations required is dependant on the
size of the system in the NR method
(d)convergence characteristics of the NR mehod are not
affected by the selection of the slack bus

Question Posted / jignesh619

1 Answers
3840 Views
I also Faced
E-Mail Answers

In the solution of load flow eqation, Newton raphson method is superior to the gauss siedal method ..

Answer / enggrashmi

ans(a)

Is This Answer Correct ?

0 Yes

5 No

Post New Answer

More Electrical Engineering Interview Questions

WHAT IS SHORT CIRCUIT STRENGTH OF 100 AMPS MCCB?

0 Answers ACC,

What is the meaning of CT 400-200/1-1 A ?

2 Answers Home,

What is SMPS,How does it works?

4 Answers Bharti, TCS,

with 3 phase board on a 63 amp rcd is it ok to have 6 electrical showers 2 on each phase and what problems could happen

0 Answers

WHAT IS THE DIFFERENCE B/W BUSHINGS AND INSULATORS? WHAT IS THE CREEPAGE DISTANCE ?

3 Answers TCS,

for 11KV OH system what will be typical per KM "R" "L" "C" parameter. for 33KV OH system what will be typical per KM "R" "L" "C" parameter. for 33KV UG system what will be typical per KM "R" "L" "C" parameter.

0 Answers wbsedcl,

what is star delta starter? how it works? give its control and power diagram.

0 Answers Bhel, Point to Point Solution, Star Wire,

what is the series parallel connection of capacitors? and how can we use these application in three phase motors for controlling torque?

0 Answers

hello if any one have papers vof hpcl or sail, plz send me

0 Answers

Based on CPI/CGPA they shortlist the candidates & than directly start Interview so there is no Written Exam or GD Only PI.Interview held @ MNNIT , ALLAHABAD On-Campus on 6th,Aug, 2007 & the Questions asked to me by Interview Board ( 4 People) are from HR/SummerTraining/BTP/Subject-core, POWER SYSTEM & MACHINE. time duration of I/V is about 15-20 Minutes. HR- Q.1 Name,hobbies & About family background ? Q2.What u know abt NTPC ?? Q3.Why u want to choose NTPC as ur Carrier's starting i.e power sector not any other Oragnisation or sector ?? Techincal Questions- Q1.What is the reason for transformer Noise ?? Q2.Which material is used for making Transformer oil & How u measure its dielectric strength & Name the test ? Q.3 Which Machine u will prefer 2 use if flammble gases are coming out at a place & why ?? Q4.What is relation b/w Transmission Lines & Communication Lines ? Q5.What is the maximum capacity Synchronus Machine & total powerGeneration in our country ? Q.6 In india Power generation is at 50Hz while in America its 60 hz ,why so ?? Advantage or disadvantage ?? Q.7 Maximum Generation Voltage in india ? Q8. What is the Voltage regulation & why its required n how much is permissible ? & causes of voltage variation ?? Q.9 Why electric shock is feel ?? n in a Electric Train why we didnt feel that ? Q.10 Have u seen/ experience of any power plant/ industry related to the power sector ? so these are the questions which not too diffcult i think was asked to me.

6 Answers NTPC,

what kn of disc is used in 33kv,132kv,220kv,400kv,800kv transmission line

0 Answers Jindal, Power Grid,

How we calculate the Multiplying Factor of Kwh meter for 3 phase alternator.

0 Answers Cesco,

For more Electrical Engineering Interview Questions Click Here