Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
I have 12MW gas engine based power plant its running parallel with grid. my problem is When cpp run in island mode(without geb) that time geb transformer power factor is 0.2 lagging. When cpp run with parallel that time power factor is 0.94 lagging So how can i maintain power factor ofgeb transformer in island mode 0.9 lagging?
SPCL,
1 2802hi can you give any body fault level calculation, generator fault level calculation,transformer fault level calculation for system fault level with equation? i have 3.3kv generation voltage three gas gen sets, one is 1.9MW,2nd is 2.5MW,& 3rd is 3.8MW & i have 11 kv generation voltage one gas gen sets is 3.8MW, we are step up to 22kv by transformer
3 8034How delta connection in the primary of distribution transformer reduces harmonics?how delta connections reduces harmonics?Please answer me...Hope that question is correct.
2183dear sir i m anshul kumar from dehradun i want to last five year railway chandigarh and allahabd entrance exam papers pls send it on my id my id is anshuldhiman83@gmail.com or anshuldhiman@rediffmail.com i shall be very greatful to u thank u
2387dear sir i want also last five year rrb chandigarh and allahabad aptitude test question and their answered my id is anshuldhiman83@gmail.com
1839how we can come to know that motor winding resistance which showing by DMM is right or wrong???is there any chart or something that we will compare & check???
1878Lux meter is the measuring device to measure the lux level of lighting fixture. in industrial sector two types of lighting fixture is being used as street lighting purpose 1. HPSV (Sodium) and 2. HPMV (Mercury). HPMV having white light which is an combination of red, blue and yellow colour, while HPSV haivng Yellow lighting. in HPSV red & blue colour will be absent. during measurement of the lux level of HPSV and HPMV fixture. 1. Lux meter can measure the actual lux level of both fixture? 2. or it will show false reading for HPSV fixture light as it has only yellow light present. please give me answer
1 6368What is the minimum insulation value required for a cable between phase to phase and phase to earth of 380 Vac 50Hz circuit, having load arround 800 amps.
2 9228what is the maximum current carrying capacity of a 95 sqmm cupper under ground cable laid partialy in land and partialy in ground?
4 7337when we megger is not damaged when we are measuring very low resistance? high d.c. voltage is produced in megger so according to i=V/R. current will be high so what is the reason ?
1 3858
You are about to take off the plane in few seconds and a catastrophic engine fails, and your captain tells you not to take off and just stay in the center line
Are there any alternatives to scraping a shell and tube if a capacity increase will make the pressure drop across the exchanger too large?
Explain the different steps of Commissioning.
what are the parameters are selected while manufacturing a single cylinder block?what are the different kind of test is conducted on it so that it can withstand with all those condition which required to run the engine efficiently.which force is act when piston slide inside the cylinder.
hai please please if any one have useful test related and interview based question plz send me at saify_0@hotmail.com i will be thankfull
What black man invented the clothes dryer?
IF TVM OF TRANSFORMER SHOWS POWER FACTOR ON 33 KV SIDE AS 0.97 LAGGING AND ON 132 KV SIDE IS 0.75 LEADING.IS THIS CORRECT.WHERE IS PROBLEM.
how to configure cisco router & switches plz provide me path steps?
What is T’Q and X’Q and X’D ? and what is saturated as well as unsaturated ?
How to identify the vitrified tile and ceramic tile by observation only after executing the job.
2- What are the percentages between excitation currents in phase (R, S and T) in ∆ and Ỵ connections in excitation Current test in transformers?
What is the most important precaution in any experiment with d.c. Shunt motor?
WHAT IS MOBILE SUB-STATION? & REALLY BENEFIT IN INDIA
why we call vestigial side band(VSB) as c3f?
How is solution annealing carried out? What type of furnace is required? Does one need to be heat in a salt bath?
