Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
while doing the structural works of a simple ground+1 villa, can the columns be continued immediately after neck columns without tie beam, while the tie beam to be done after columns concreting.
XYZ,
1605Can anybody please tell me from where I can get sample placement papers so that ii can prepare accordingly.
1554Question 81 - (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.
1 2495for basic costing, how can we calculate how much amount of steel and cocrete will go in per sqft? and what are the thumbrules?
1 2758what is difference between speed mode and torque mode in motor?? explain in simple words please.
1560If more than rated DC voltage appears across trip coil of the breaker, what will happen? e.g. in 110V DC circuit system, if voltage across battery terminal showing 121 V
1615
if we install two earth pits with a clear space of 5m without any interconnection,by checking the digital multimeter will it show continuity between earth pits? If so what would be the approx. value
What is polar plot?
what is the reason the main breaker is trip during the motor is running? (some time the breaker is not trip)
What is meant by optimization and what are different ways of optimiztion?
What is characteristic of ideal opamp?
Sketch the jacket cooling system?
I have a situation to design sub-Distribution board/Panel meant for feeding power sockets. In the incomer CAN i Take TP MCCB with Neutral Link and All the outgoing feeders with to sockets with TP MCCB and Neutral Link? P.S : My System is IT Earthing
Why L.T.Cable voltage rating is 1.1kV,where as system voltage is 0.415kV?
draw the interface diagram of 8085 microprocessor having input ports at 23H, 2FH, EFH, and output ports at 44H, 2FH, EFH, and FFH using NAND gates only.
what is the power factor used by the PHCN in nigeria? 2. what is the difference between an alternator and generator. 3. Generation of poweris in KV but how is transmission is in MW. 4.If the transmission of power is 20,000MW how can it be increaesed to 80,000MW
The resistance to the vehicle motion whose magnitude remain constant with respect to the vehicle speed is a) Resistance due to gradient b) Resistance due to the road c) Resistance due to the tyre friction d) all of the above
Mention some of the specialized grinding methods?
Why does the radius of armature is less than the radius of pole shoe?
prove that power consumed in 3 phase delta system is 3 times as compared to 3 phase star system
What is the automatic voltage regulator with servomotor?
