Answer / tubelight

at the time of starting the current will be very high.
to limit the current choke is used. by mutual induction
choke opposes the rate of change of current. and reduces
the change in current flow.
the high voltage production is only due to the usage of
capacitor.
that only produces high voltage.

Answer / natarajanramkumar

1.It gives high voltage impulse for starting the lamp(about
1000 volts while starter opens)
2.Its gives low voltage(110V)while running.
3.It acts ballast.Ex.smoothens the current when the lamp is
running.

Answer / neeraj kumar dhillon

WHENEVER THE SUPPLY IS GIVEN TO THE TUBE
THE CHOKE WILL GIVE SUPPLY OF 1000V TO THE TUBE AND
TUBE GET IONISED AND FINALLY GLOWING ONCE IT STARTS
AFTER THAT STARTER IS OUT OF CIRCUIT

Answer / moin

I think choke limits the current when current flows through
the ionized gas

Answer / madhu

when tubelight is on , due to choke voltage is increased to
1000 v and the gas in the tube light is ionised at this high
voltage . to ionise the gas in the tube light we use choke

Answer / akshneel sharma

IT IS USE TO PROVIDE VOLTAGE . APROX 1000 - 1500

Answer / ekta sengar

choke is a combination of inductor and resistance used to
maintain the sufficient voltage required by the tube light,
after the starter has already provided the high initial
voltage to start the tube light.

Answer / anand biradar

Choke provides high viltage(nearly 1000v) at starting
time . later on it regulates the voltage.

Answer / yuvaraj

it provides high voltage at the time of starting and
regulates the voltage at the time of glowing.

Answer / sanjay

what is the function of bimetallic element ??

i have install 750 kva distribution transformer at my site and want to do neutral earthing. what calculations should i follow to determine earthing conductor material and size?

0 Answers   MTDC,

what you mean by frequency of an igbt& how to find it?

1 Answers  

voltage of a ckt is measured by volt meter having an input impedence camparable with the out put impedance of the ckt Eror caused is 1. Gross Error 2. Errors due to lloading effect

2 Answers   GATE,

there is an alternator 480 k.w, 400v,50hz, 4-wire running on load having leakage alternator body earthed current 38 A. is it within acceptable limit? if yes then give reference if no then how to bring within specified limit

0 Answers  

can we use transformer for 70 Hz?

6 Answers  

what is the difference between elcb,rccb,mcb.

8 Answers   HCL, RCCB,

what happend when 230v dc motor we supplied a 23v ac supply

3 Answers   Hero MotoCorp, RRB,

how to calculate a cable size while load is given in amp or kw and length is also define.?

1 Answers  

an amazing situation was faced when an alive distribution panel with 415 volts and carrying almost 200Amps has become short and this metal cubical showing 220 volts against neutral and earth. to redress any confusion i checked the panel with help of single 200watts test lamp which also glowing with max.intensity b/w neutral & metal body of DB. amazing situation is that i hold the DB firmly more than once with necked foot means without insulated shoes but not received any electrical shock. whereas our all running gen sets neutral points also proper grounded and this short DB was completely earthed , this is beyond my understanding . any body explain how is it possible . our running gen set neutral also grounded firmly

1 Answers  

If a manufacturer decribes a power supply transformer as providing a secondary voltage of 24 volts when connected to a 240 volts supply, do you think they are refering to the full load or no load secondary voltage?

3 Answers  

why in generating station generation voltage is 11 kv

1 Answers   L&T, Usha Martin,

how can we check the earth resistance

3 Answers