Interested to Buy Any Domain ? << Click Here >> for more details...
what is the use of choke on tube light fitting
- 37 Answers
- 81247 Views
- Bhel, Dharma, HSBC, TCS, I also Faced
- E-Mail Answers
Answer Posted / akshneel sharma
IT IS USE TO PROVIDE VOLTAGE . APROX 1000 - 1500
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
how do we calculate length of starting time and repeated starting of a direct online starter?
how to measure the transformer resistance values(dyn11)?and howmuch the minimum value?
Earth is a conductor or load?then ammeter connect to 3- phase supply,it shows the measurents or not?
how the testing of protection CT Testing done through Primary injection kit please describe in detail procedure...
Write the force balance equation of ideal dashpot element.
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
how to calculate the capacitor to maintain power factor?
What is the need for a controller?
Why you want to join non technical field when you are an engineer?
if in 3-phase system voltage=440V,frequency=60Hz, current=400A. then if it is single phase then current=? and if it is single phasing then current=?
what happen when power factor of 2 parallely operated transformer become equle?
is there any device that works properly accept relay, it may be fuse but if i want fuse of 33kv 300 amp it is avaliable, pls give me details
Why there are some equipment(i.e:TV) that using 2-pin plug instead of three? What happen if there is current leakage? Are we going to get electric shock??
Where should the lighting arrestor be placed in distribution lines?
I have a current transformer with 1 main reading meter with transformer outside the building and a control panel having 5 CT reading meters with black round coils inside the building. I want to know, A) when current pass through the Transformers, will the current be reduced or be the same and after that B) when current pass through the CT meters with black round coils, will the current be reduced or be the same. C) in the above process will the reading of the main meter be same or different, from the total reading of all the 5 CT meters.
