Interested to Buy Any Domain ? << Click Here >> for more details...
can we use 220 volt 15 w a.c. lamp on 220 volt d.c.
- 11 Answers
- 22424 Views
- Philips, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / k.ravindran
220VAC is the root mean square value of the AC supply
provided by the electricity authority. It has the same
heating effect as 220V DC when the load is resistive.
Incandescent lamp is a resistive load.
| Is This Answer Correct ? | 14 Yes | 3 No |
Answer / ritesh gupta
yes, if lamp's filament is coil type, not in case of gaseous
discharge type
| Is This Answer Correct ? | 10 Yes | 1 No |
Answer / lakshmi narayanan
YES, IF IT IS AN INCANDESCENT LAMP.
wat ravindran said s right
| Is This Answer Correct ? | 8 Yes | 1 No |
Answer / ravi shah
Yes We can use 220V AC lamp on 220V DC supply because of
basically the lamp is made of filament which is a resistor
only and there will be same effect on resistor on both AC
and DC supply,Also on DC supply The light of the lamp will
be higher than AC supply.
| Is This Answer Correct ? | 6 Yes | 2 No |
Answer / dhiren
yes we can give 220v to ac lamp because the relation of ac &
dc in term of resistive load in heating.
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / pratheesh
We can say light is the result of heat produced in the
incanscent lamp filement.
So Heat produced= square of current* resistance of that
filament*time.
It is same in DC as well as in AC also(As it is pure
resistive load)
| Is This Answer Correct ? | 2 Yes | 3 No |
Answer / vidhya
cud u justify ur answer...y tis alone havin this
capability...
| Is This Answer Correct ? | 1 Yes | 4 No |
Answer / v.sivakumar
inchancent lamp flement is inductive type so it is work
with ac&dc
| Is This Answer Correct ? | 1 Yes | 4 No |
Answer / girish kumar samal, hindalco,h
no as it design for ac 220v.if it can used in dc ,then the
manufactor nt write ac on name plate.
| Is This Answer Correct ? | 3 Yes | 10 No |
Hai I have 2500KVA,Transformer,13.8KV/380.DELTA/STAR.How much load that I can take interms of current?How can I calculate also when I have loads in KW?
Could Please Explain briefly. Why used stabilizing resistance series with High impedance bus differential protection relay.
How to control speed of DC motor with AC power?
why voltages are added when batteries are connected in series?
why two point starter,three point starter, four point starter cannot be used for A.C machines?
How can i learn to programme every VFD. Or is there any typical study to understand VFD programming.
What is the minimum distance between MV busbare (P to P & P to E) as per some standards
temp of cast resin 1500kva tx formerwent up to 138.c but came down very fast to about 100.c within 20 mins when load was reduced from 70% to 60%
why ht line fuse wire is so thin
what is the diffrantial relay???????why we use it on the MDB
How can we calculate the power factor of an electrical appliance ? Is there any formula ? Is there any meter around to calculate it ? And how to use that meter ? thanks
Difference between 3.5 core and 4 core
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
