i have 2 motor of same rating. on no load condition one
motor take 1.6A but other motor is taking 4.8A. what is the
reason of this. please explain with proof.
- 8 Answers
- 8373 Views
- Ambuja, UltraTech, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / b.b. singh
one motor has connected in star then it taking 1.6A &
another is connected in delta so it taking 4.8A.
| Is This Answer Correct ? | 16 Yes | 1 No |
In case of 3 phase motors,
the motor takes higher current might have incorrect winding ratio which may cause unbalancing of 3 phase current.
| Is This Answer Correct ? | 2 Yes | 1 No |
Answer / ashok sharma
OK. It is right that in star motor taking 1.6A & in delta
motor is taking 4.8A. but Please prove this with example.
Suppose both motors are new .
| Is This Answer Correct ? | 0 Yes | 2 No |
Answer / sivakumar
FIST U WILL CHEK THE HP RATHIG THEN NEXT CHEKED AMPS
| Is This Answer Correct ? | 0 Yes | 2 No |
Answer / loboreliance2003
The motor drawing 1.6A on no load appears to be okay.The
motor drawing 4.8A on no load appears to have a fault. the
winding may be having not proper megger value. Or even
rewinding of this motor may have been done improperly. You
will not find this condition in new motors from original
manufacturer.
| Is This Answer Correct ? | 2 Yes | 5 No |
Answer / sakthivel
first you are check the bearing and terminal board and all
so check starter conduct knob and verify the electrical
parameter and all check pump and so impellerside
| Is This Answer Correct ? | 0 Yes | 3 No |
Generally In transformer Tap Changer on HT side, but I have seen in 66KV side in 220/66 KV, 100 MVA, Areva make transformer. Why ?
Why we are putting off the APFC(automatic power factor control) panel while the generator is running?
A 50Hz,4-pole,3-phase,star-connected synchronous motor has a synchronous reactance of 12ohmsper phase and negligible armature resistances.the excitation is such as to give an open-circuit voltage of 13.2kilovolt.the motor is connected to 115kilovolt, 50hertz supplying. what maximum load can be the motor torque,line current and power factor?
what is the differnce between ac and dc?
what is per unit calculation?looking for simple and strong explanation thk u
two 100W/230V bulb are connected in series. what would be the voltage drop across 1 bulb
1. what is difference between VCB and ACB.how its works please explian.
6 Answers ABB, Accenture, HP, Minda, Mother Dairy, Satyam Pharma,
I have a shop heater with a 1/3 hp capacitor start, induction motor driving the fan. Intermittently, the fan motor speeds up significantly for several seconds (15-60 sec) then slows to normal operating speed. The manufacturer suggested changing the capacitor which made no sense, but I did it to no avail. Could this possibly be caused by the centrifugal switch intermittently reconnecting the start winding?
Can anyone tell me some hints about what type of questions are asked by the interviewer by an Electronics engineer when company is installing an IPP and wants a team of engineers?
what is the role of energy meter in distribution system ?
why connecting surge unit in contactor coil
Transformer calculation
1 Answers Aramco, LMW Lakshmi Machine Works Limited,
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
