What do you mean by PT-100?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / engrutm

8 Answers
24983 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What do you mean by PT-100?..

Answer / mohit.k.k

pt 100 is instrument for detecting temperature and it is
resistance temperature detector ( R.T.D) detects resistance
of platinumused in it. range is about -200 to around 800*C.
it has resistance of 100 ohm at o degree celesius.

Is This Answer Correct ?

48 Yes

3 No

What do you mean by PT-100?..

Answer / rajkumar

PT-100 is normally used in RTD, its a temperature sensing
element, basically called as platinum 100, for positive
temperature co-efficient,if temperature increases
resistance also increases, the increase of resistance is
due to the applide voltage passing through the sensing
element, it has resistance,for 0 degree celcius 100 ohms.

Is This Answer Correct ?

22 Yes

3 No

What do you mean by PT-100?..

Answer / genjua

pt-100 is a tempertaure sensor!
widely use in industry becoz it is LINEAR!
resistence increase with the increase of temperature

Is This Answer Correct ?

23 Yes

8 No

What do you mean by PT-100?..

Answer / vibhuti gupta

Pt -100 is a temp sennihg material at zero degree it
resistance 100 ohm when we increase the temp its resistance
also increase

Is This Answer Correct ?

16 Yes

5 No

What do you mean by PT-100?..

Answer / priyesh gajjar

pt100 is a type of resistance temperature detector ( R.T.D.
).it is use for temp. measurement.resistsnce is linearly
vary with tempature. it has 100 ohm resistsnce at odegree
celcius.

Is This Answer Correct ?

9 Yes

2 No

What do you mean by PT-100?..

Answer / anirudh

PT-100.
it is RTD which is used to sense the temperature.
where PT=platinum. i.e platinum is used as resistance.

Is This Answer Correct ?

9 Yes

5 No

What do you mean by PT-100?..

Answer / ronny govender

is a component of liner escalation as the temp increase the
resistance increases

Is This Answer Correct ?

5 Yes

6 No

What do you mean by PT-100?..

Answer / navnit

pt-100 is a temperature sensor
which we can use for 0-100 degree temperature

Is This Answer Correct ?

8 Yes

22 No

Post New Answer

More Electrical Engineering Interview Questions

WHAT IS DOL STARTER? HOW IT WORK? GIVE ITS CONTROL AND POWER DIAGRAM .

0 Answers Bhel,

what is basic difference betmeen normal & flame proof motor??

0 Answers Dynamics,

Define steady state error.

0 Answers

It is used or not HT cable single core 630 sqmm in LT 3 phase capacitor bank which is used in PCC(power control center).

1 Answers

If my sfu is 64 Amp & its link is 32 Amp then at what amp.my sfu will trip???

2 Answers

how the 6.6KV motor can be used with 11KV?

2 Answers

in alternator how we can give power to rotor ? its power is AC or DC ?

5 Answers

Write the current equation in series RLC circuits.

0 Answers Agilent, Integreon, ZS Associates,

How to determine earth fault level to set relay for a normal distribution system of 11 kV , 100 A load????????

1 Answers TCS,

what happens if you swap F1 and F2 connection in the exiter of the generator?

1 Answers

I am getting above 60 V as open delta voltage against single phase unit ICT at tertiary delta formed and ICT getting trippped on NDR. ICT tested and found in order. PTs provided on tertiary are tested and in order. what may be the reason?

0 Answers

why it is in star to delta form of Synchrounus generator and delta to star form of Generator Transformer (or step up transformer)

1 Answers

For more Electrical Engineering Interview Questions Click Here