What is the diffrece between ACB & MCCB
Answers were Sorted based on User's Feedback
Answer / ektate prashant
ACB- Air circuit breaker
MCCB- Moulded case circuit breaker
Arc Quenching medium in both the breakers is air only.
The difference is ACBs are of higher capicity as compared
to MCCBs.
| Is This Answer Correct ? | 25 Yes | 1 No |
Answer / ashutosh
The Main Differnce in Acb & Mccb is that Acb is Used For
Higer Cureent Rating >800A While The MCCB is Used For Lower
Cureent Rating<800A
| Is This Answer Correct ? | 25 Yes | 8 No |
Answer / akash-ncl
ACB- AIR CIRCUIT BREAKER
MCCB-Moulded case circuit breaker
Quenching media is same for both
Protection features which consumer can set will available
with acb i.e o/c,o/c time,sc amps,sc current interrupt time
and ground fault limitings
and lost and most,
short circuit limiting capability Isc is more with acb
selection of acb/mccb depends upon device,fault
level,application and economical calculation since cost
diff is most considerable here
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / nagaraja
ACB-Air Circuit Breaker ,MCCB-Moulded Case Circuit Breaker.
ACB using for higher current ratings and MCCB using for
lower current ratings.
ACB works under voltage as well as over current,But MCCB
will not works Under voltage.Only over current(new mccb
having under voltage fecility also through closing coil
intrudusing)
| Is This Answer Correct ? | 4 Yes | 4 No |
Answer / rajesh tewari
acb for more then 900 amp and mccb is less then 900amp.acb
protection in short ckt .open ckt. earth fault.ground
fault.unbalanced load.and dispaly it in digital vidio
dispaly.but mccb gives us protection bnut not dispaly
| Is This Answer Correct ? | 4 Yes | 4 No |
Answer / vijay kumar
air circuit breaker is use to open and close the circuit at normal and fault conditions
but motor control circuit board is used to control the motor current at starting and running conditions and also phase transformation like star to delta and delta to star connection
that is the basic deffence
| Is This Answer Correct ? | 0 Yes | 1 No |
Why is the frequency not changed during transformation of electrical energy in a transformer?
what is High resistance grounding and whatis the criteria for the selection of High resistance grounding
what is the impedance voltage of transformer?
1 Answers AVI Enterprises, MacLellan,
I need a formula to calculate the size of cable as per load but in the terms of length. Please Reply me as i search lot of sites but i did not get the answer.
what is EIB lighting control system? what is the advantages of this system?
What is power relay?
What is a soft start?
If a shunt Dynamo has induced emf 100V and 0.4 ohm resistance and battery of accumulator of open circuit emf 110V and 0.5 Ohm resistance are in parallel what is common terminal potential difference?
What are the typical values of characteristic impedences of overhead line and underground cabel? Why there is so much variation?
how to check the LRS resistance .......................
Kindly Tell me name of the book for electrical estimation and costing ,calculation or web site to download
first 3 men were there .again 3 came.total how much?
Civil Engineering (5086)
Mechanical Engineering (4453)
Electrical Engineering (16638)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)