What is the acceptable percentage of slump in Mix concrete?

Categories >> Engineering >> Civil Engineering
Suggest New Category

Question Posted / miidangriika

9 Answers
26929 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is the acceptable percentage of slump in Mix concrete?..

Answer / jeelani.mohatad

Depends on the grade of concrete, the mode of reinforcement
being used and the method employed at sute for placing the
concrete.for pump concrete 100mm min slump is reqd. for
chute upto 75mm is taken acceptable

Is This Answer Correct ?

38 Yes

4 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / thaiv

Description Slump Range
mm In.
Very low 0 to 10 0 to
Low 10 to 30 to 1
Normal 30 to 60 1 to 2
High 60 to 180 2 to 7

Is This Answer Correct ?

14 Yes

4 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / maheswaran

from is 456-2000
Lightly reinforced 25 – 75 mm
Heavily reinforced 75 – 100 mm
Trench fill (insitu & Tremie) 100 – 150 mm

Is This Answer Correct ?

10 Yes

0 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / mahesh_pandey05

IF WE TAKEN DESIGN MIX .IT ALREADY MENTIONED THERE.120MM MINIMUM FOR PUMPING OF CONC.

Is This Answer Correct ?

8 Yes

0 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / vijay kumar.g

depend upon the work(is:456-2000)

mass concrete and lightly reinforced sections(beams columns,walls and slabs)25-75mm
heavily reinforced sections(beams columns,walls and slabs) and pumped concrete and trench fill 50-100mm
flow able concrete 100(+/-)20

Is This Answer Correct ?

6 Yes

0 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / vasanthsibi

50 to 100 normal
100 to 160 high
Above 150collapse

Is This Answer Correct ?

0 Yes

0 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / ramir v. agustin

150 + or minus 25mm as per bs standards

Is This Answer Correct ?

7 Yes

8 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / sakthi

FROM THE SLUMP TESTING EQUIPMENT WE CAN FIND OUT THE RESULT
OF SLUMP.

BUT,

MORE THAN 125MM IS HIGH FLOWING CONCRETE,SO NOT ADVISABLE
FOR CONCRETING.

LESS THAN 25MM IS VERY HARDEN CONCRETE HAS LESS PLASTICITY.

FROM 25MM TO 125MM WE CAN USE AS PER TYPE OF CONCRETING.

Is This Answer Correct ?

3 Yes

5 No

What is the acceptable percentage of slump in Mix concrete?..

Answer / anwar

150mm min slump is reqd.
30mm is tolerence

Is This Answer Correct ?

7 Yes

12 No

Post New Answer

More Civil Engineering Interview Questions

what is the best method for analysing frames of multistoreyed structures

2 Answers

How do you change a dimension value in solidsworks?

0 Answers

deshuttering time for RCC for DPC over the foundation.

4 Answers

one litre of shuttering oil how much area covered the shuttering?

5 Answers UltraTech,

Is it possible 18" beam rest on 18" beam and created the junction on beam instead of column?

1 Answers Nespak,

How to build the floor to ceiling bookcase?

0 Answers

what is idealized curve for concrere and steel

0 Answers CSIL,

why the compressive strength of concrete is calculated only after 28 days.why not after 25, 26,27 days..

7 Answers

I used Etabs software to analyse a high-rise building. And I want to use templated UBC-codes inside to calculate the Seismic load. My question is: whether or not I have to control the seismic load by base shear load which is manual calculation? (just for more clarification: I can control this by input the scale factor into Eartquake definition in Etabs) I would highly appreciate your answer.

0 Answers

how to prepare Steel schedule or Bar bending schedule.

1 Answers

how to calculate rate analysis for column shuttering

2 Answers L&T, Marg,

how would you describe yourself and your ideal job

3 Answers

For more Civil Engineering Interview Questions Click Here