WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS




Answers were Sorted based on User's Feedback



WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS..

Answer / vivek

When Diesel generator overload its freqency reduce fron set
value ,so RPM of dg decrease as result .Fuel governer
direct control the speed of engine .when sensor actuate it
stop the engine.

Is This Answer Correct ?    18 Yes 0 No

WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS..

Answer / lokesh

Even diesel gen cannot hold the over load when it reaches
perticular load it tripps for safety purpose

Is This Answer Correct ?    4 Yes 4 No

WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS..

Answer / mubanga mulenga

its because it reaches past its steady state stability
limit, delta 2, so it will swing out into trip.

Is This Answer Correct ?    1 Yes 2 No




WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS..

Answer / deltawye

the diesel generator set will shutdown during overload is
because of its voltage regulator

Is This Answer Correct ?    0 Yes 1 No

WHY DISEL GENRATOR SET SHUT DOWN IN OVER LOAD CONDITIONS..

Answer / sarfraz

In my views
for few second it will support then safety operate and it
switch off the genset

Is This Answer Correct ?    1 Yes 5 No

Post New Answer



More Electrical Engineering Interview Questions

what is the tolerance of electrical frequency for India? it's .5% or 1%?

8 Answers   Engro,


How we can change the direction of rotation of Induction motor? Prove it using graphical

0 Answers  


why in power staions distriution r like 11kv,33kv,66kv in india?

4 Answers  


I have an 15A fuse MCB that controls a night storage heater. It needs replacing and is now obsolete. Is a 16A C curve MCB the correct replacement?

2 Answers  


how actually an anti pumping device works? what is the operational principal?

2 Answers  






What is Diff btw MCP & MCB????

10 Answers   Suzlon, Emerson, Athena,


i have a Connected Load of 280KW and Maximum Demand of 224KW to one of SMDB under design with me. which criteria should i consider to design panel and main cables connected Load or Maximum Demand 1)Breaker rating 2)Panel Busbar rating 2)Incommer cable sizing (ignore Voltage drop)

1 Answers  


Dear All please ive me ur ideas... What is the major diff between cu conductors and Al conductors ?

3 Answers   MX Technology,


What is basic difference between Soft Starters And VFD drives?

19 Answers   IBM,


What is the difference bet ween EDO Type & MDO type ACBs, and what is the advantage EDO Type over than MDO type ACBs.

2 Answers   Siemens,


will we have to design the UPS differently for both i.e. if we want to connect the two batteries in parallel and/or we want to connect the two batteries in series ?

4 Answers  


where is the primary of CT??

3 Answers  






Categories
  • Civil Engineering Interview Questions Civil Engineering (4631)
  • Mechanical Engineering Interview Questions Mechanical Engineering (3698)
  • Electrical Engineering Interview Questions Electrical Engineering (15757)
  • Electronics Communications Interview Questions Electronics Communications (2635)
  • Chemical Engineering Interview Questions Chemical Engineering (761)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (79)
  • Bio Engineering Interview Questions Bio Engineering (30)
  • Metallurgy Interview Questions Metallurgy (95)
  • Industrial Engineering Interview Questions Industrial Engineering (199)
  • Instrumentation Interview Questions Instrumentation (2875)
  • Automobile Engineering Interview Questions Automobile Engineering (171)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (41)
  • Marine Engineering Interview Questions Marine Engineering (62)
  • Power Plant Engineering Interview Questions Power Plant Engineering (169)
  • Engineering AllOther Interview Questions Engineering AllOther (1332)