Answer / raj

concentrated wdg means one phase wdg under one slot only.
in distributed wdg one slot accomodate two or three phase
wdg i.e. more than one.

Answer / ramya

distributed winding is one in which the windings are
distributed along a number of slots. the major merit of
this is the heat dissipation is better.
whereas in concentrated winding, the windings are
concentrated only on one slot. here, since more number of
coils is in one slot, the heat produced is more.

Answer / engineer aamir ali

A winding with only one slot per pole per phase is called a
concentrated winding. In this type of winding, the e.m.f
generated/phase is equal to the arithmetic sum of the
individual coil e.m.f.s in that phase. However, if the
coils/phase are distributed over several slots in space,
this kind of winding is called distributed winding. The
e.m.f.s in this case are not in phase but are displaced from
each other by the slot angle. the e.m.f will be the phasor
sum of the coil e.m.f.s.
REFERENCE: Principles of Electrical Machines By V.K Mehta

Answer / sanni kumar

in concentrated winding all the winding turn are bound
togater in series to form one multiple coil ex-transformer ,
d.c machine.in distibuted winding all winding turn arranged
in several full pitch or fractional pitch ex-in induction moter

Answer / davod habibinia

Concentrated winding in 3 phase armature means that the value of distribution factor (kd in many references) be equal to 1. It means that the winding is concentrated along a pole. 
In distributed winding the value of kd in the base winding (machine period) is below 1, which determines that the value of the induced EMF in one phase is less than the value of "induced EMF in one coil * number of coils series in one phase" . 
With this definition the only winding in 3 phase anrmature which have concentrated winding is the machine having q=1 (q is the number of slot per pole per phase) . 
Then there is machines which has the winding with one slot pitch (q=0.4), but illegally said to have concentrated winding but actually the winding is distributed with kd=0.9659 and kp=0.9659 and therefore kw=kd*kp=0.933. (Kp is pitch factor) . The value of winding factor (kw) could be determined with star diagram of winding, and pitch factor too, then we can see that the kd will be lower than one for this machine (q=0.4).
These type of machines which has one slot pitch for the each coil of their winding are called "tooth wound machines" and not concentrated. 

Answer / siva

concentrating winding means winding which is wounded at a single slot or place or position (say field pole) so that flux produced as a combination is more concentrated and also dissipation is high as heat loss due to both current through it and of adjascent winding heat and it is low power winding.where as distributed winding means winding is distributed along a number of slots and it is high power winding.

Answer / silamparasan p.

For Example:

Concentrated winding-Transformer

Distribution winding-Induction motor

How can you calculate in detail the VA burden of current transformer used for Restricted earth fault protection? Please understand that the CT required here is Class PX or X. Also please show the calculations for knee point vtg, stabilizing resistor, magnetising current.

3 Answers  

In general bus riser follows the bus section in SWGR. What are impacts if bus section follows bus riser?

0 Answers  

What is hysteresis losses?

2 Answers   GMR,

what type of relay has to be used for tripping the circuit from mains when a fault occur in a machine

3 Answers  

c++ write a program to use a fuction call "max"which accepts an intger arrey of size5.as an arrument and return the larger and smallest of the arrey to main without changing. the original changing of the original position of the element of the arrey.

0 Answers  

how the calculation is done if the DG set require for the -- -48 to -51v 4000 ah battery set .

1 Answers   BSNL,

how to calculate power

3 Answers  

What is Ten Delta Test ?

8 Answers   Areva,

I WOULD LIKE NOW WHY WE CANT USE SOME CT FOR MESARING AND PROTECTION

2 Answers  

how synchronous condenser is used in place of synchronous generator with out negotiating IEEE standards? Can i use 3 generators as synchronous generators and 2 generators as a synchronous condensers in an IEEE 14 bus system with out disturbing the standards?

0 Answers  

can i know how to design overcurrent setting and earth fault for 11kv & o.433kv system assuming tx 1000kva.

2 Answers  

how work the differential protection relay in details?

2 Answers