when a three phase motor in running condition consumes 2A in each phase,and if

when a three phase motor in running condition consumes 2A
in each phase,and if one of the phase gets fails what will
be the consumption in other two phases

Question Posted / powerselvan

4 Answers
6589 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

when a three phase motor in running condition consumes 2A in each phase,and if one of the phase ge..

Answer / j.kesavan

when one phase fail ,other two phase take more current,coil
will burn out.

Is This Answer Correct ?

7 Yes

1 No

when a three phase motor in running condition consumes 2A in each phase,and if one of the phase ge..

Answer / prashant

for a three phase motor do work properly all the 3 phases
must be active. In case if one of the phases fails then the
motor will not work properly ( SHOULD ACTUALLY STOP
ABRUPTLY )and may probably give a loud whining noice.

Is This Answer Correct ?

6 Yes

2 No

when a three phase motor in running condition consumes 2A in each phase,and if one of the phase ge..

Answer / pratheesh

If one of the phase fails when a 3phase induction motor
is running, motor will continue running with a 25
percentage of more current in other 2phases.
If the thermal overload protection is not working
perfectly, the motor winding may burn.

Is This Answer Correct ?

4 Yes

2 No

when a three phase motor in running condition consumes 2A in each phase,and if one of the phase ge..

Answer / gunasekaran

another two phase draw almost 2times current so winding may
getting heated up negative sequence relay will operate

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.

0 Answers Piramal Healthcare,

What is the polarization index value ? (Pi value)and simple definition of polarization index ?

0 Answers

How can we calculate the power factor of an electrical appliance ? Is there any formula ? Is there any meter around to calculate it ? And how to use that meter ? thanks

2 Answers Essar, Philips,

Under wat condition statcom operates as an inductor for the transmission line?

0 Answers

how to calculate cable size in diffrent loads?

0 Answers ABB, Sterling,

pls tel me the electric train traction motors name plate details like rpm,torue,voltage,amps,watts..ect..

0 Answers

When geneartor is running in poor lagging side power factor its excitation current increases then it is running in improved lagging side.Kindly tell me when gen is running in leading side what will happen

3 Answers

what happens in the primary side of the transformer if transformer is short circuited first and increasing the resistance of the short circuit gradually?

3 Answers Emerson, IIT,

whatis mean by voltage?

7 Answers

a 25kvar capacitor bank connected to the secondary side of transformer.then why the capacitor draws more current then rated

3 Answers TATA,

what is defference by mcb,mccb and mpcb

4 Answers Bhel,

in an electronic tri vector meter when the current and voltage sequence changes ? what is the effect of phase sequence on recording of meter

0 Answers L&T,

For more Electrical Engineering Interview Questions Click Here