Answer / govardhana rao.p

Calculations are same as above but for 50A load

We can use the bellow cables

Aluminium: 50 x 3.5 Core

Cu : 16 x 4 Core

Answer / sabu

in case 50amps 230v single phase load we can use 16mm aluminium and 10mm copper

Answer / zafar

the answer is not correct the correct figure is 25mmsq

Answer / bipin naik

The current will be 27 A for single phase supply(230v)

Answer / fathi

2x10 sqmm Cu/XLPE/PVC 600/1000 v

Answer / engr.muhammad younas khan

SINGLE PHASE FORMULA FOR CABLE SIZING.

REQUIRED DATA:-
I :- AMPERES
L :- LENGTH OF CABLE.
K :- CONDUCTIVITY OF COPPER(58)
:- CONDUCTIVITY OF ALUMINUM (36)
Vd:- VOLTAGE DROP.

GIVEN DATA:
I:- 50 AMPERES.
L:- 100 METERS.
Vd:- 3% ACCEPTABLE OF 230 VOLTS

FORMULA:-
AREA (mm2)= 2*I*L/(K*Vd)
= 2*50*100/(58*6.9)
= 24.98 mm2
= ALMOST 25 mm2
FOR THREE PHASE:
AREA(mm2) = 1.732*50*100/(58*12)
= 12.44 mm2
= ALMOST 15 mm2
3% voltage drop of 400 volts =12 volts.

ABOVE EXPLAINED FOR IS PROPERLT CORRECT.USE AND ENJOY.

ENGR.MUHAMMAD YOUNAS KHAN
M.SC.ENGG.MIEE(UK)
WAZIRABAD CITY,PUNJAB, PAKISTAN
DATE:- 24/3/2014

Answer / selvakumar

230 meter cable

Answer / lorp soophan

S=(2.l.i.cosg)/V%

Answer / vinay katoch

formula is same but for 50 amp load we can use 3.5c
25mmseq.all.and 10mm seq.cu.

Answer / gurunadharaov

by the formula p=v*i*cos@
assume the load as 5kw and operating at 230v and also
assume the load as inductive (so the power factor is 0.5
pf lag)


now by formula
5000=230*i*0.5
i=50A
NOW CABLE SIZE MUST BE > LOAD
SO CABLE SIZE IZ 65SQMM(ITZ DSSEPEND ON AL/CU CABLE)

Why don't we use ground free electricity to avoid electric shock.As birds are do not get shock.

3 Answers  

Tell me harmfull effects of over voltage,under voltage,spike,surge,transient & noise.

1 Answers  

Is there any particular formula for sizing the bus bar based on the current rating

1 Answers   Bunt Solar,

Hydro P.P. run @ 600 rpm,8pole, Nucler P.P @ 1500rpm 4 pole , ThermlP.P @ 3000 rpm 2 pole.Why this diffrence??? when we can generate electricity @ 600 rpm then Why we had incresed speed in NPP & TPP???

3 Answers  

What is a roll of adopter panel in terms of h.t. Panel ???

1 Answers  

suppose if oil in transformer is not used than what constructional change you will do,for insulation and cooling?

2 Answers   ABB,

Whats the minimum value for I.R. that can be allowed for HT & LT alternators for operation?

1 Answers  

Classify milling machines.

0 Answers   Ashok Leyland,

To generate electricity , what is the speed of rotor?

1 Answers   JEC,

what is hysteresis loss?

4 Answers   PSU,

which oil used in transformer?

5 Answers  

Z transform is use when system is not a) converges b) diverges

0 Answers   CCP,