Answer / victor vgp

no
if we take three pin socket(power socket) it has three pins
at bottom it has two pins of similar size's one is for
phase and another one for neutral which is mean for return
path of the circuit and
another pin in top is earth which is comparitively larger
in size because it's mean to take unwanted fault current to
ground
so that neutral is a return path to the circuit and earth
is meant for earthing the fault current
r u got it?

Answer / abid mirza

no! hum nahi mila sakte neutral or ground ko kunke neutral
ek path complete karne keliy hota hai aur ground hum safety
keliy istamaal karte hai jis mein buhut hi kam resistance
hoti hai ok

Answer / harun kumar

HI DUDES.ACTUALLY NEUTRAL IS THE INTERSECTION POINT OF ALL
PHASES,AND EARTHING IS DONE BY USING BIG EARTH SPIKES WITH
FULL OF EARTH MAT,SO FINALLY EARTHING IS THE PATH FOR
DISCHARGING FAULT CURRENT,NEUTRAL IS FOR FLOW OF REVERSE
CURRENT,SO THAT WE GET CIRCULATING CURRENT IN THE CIRCUIT

Answer / sanjay

neutral is used for circuit complition means for return
path of current.
& earthing is used to flow fault current to ground safely.
neutral & earthing are two different things.

Answer / jagannath sahu

no we can not connect the neutral with earth as in the
transformer neutral is already grouned.as we know neutral
carrying same current,that phase line in case of single
phase.so neutral is grounded only in case of 3phase
circuit,not in single phase.

Answer / suresh reddy

he dude actually that is wrong

see the purpose of neutral is to complete the the circuit
as well as retrun path for excess current &
same grounding is to deliver likage (fauilt) current to
save equipment and person

we can not short the ground and neutral together keep in
mind

Answer / ashok

Answer is NO....
Bcoz.. If you joined the neutral & grounding point... then
there is no closed path......... therefore ckt in open
position

why are the likely reasons for bochholz & pressure relays oprate due to a internal fault but not differential relay ?

2 Answers  

1)what is the function of a frequency inverter? 2)If a few frequency inverter are connected onto a device network,what are the two setting that will ensure the frequency inverter work properly on the network. 3)whats is the name of the input sensor for weigher? 4)How to confirm that the load cellis faulty? 5)Describe briefly the steps to validate that the weigher is working properly? 6)Describe the procedure to validate the flowmeter accuracy? 7)Describe briefly the steps to validate that the tempreture sensor/transformer is working properly. 8)what is the adjustment that need to be done when you are calibrating the temperature transmitter ? 9)what are the safety measures to be taken before disconnecting motor for rewinding. 10)whats is the synchronous speed in rpm of typical 4pole 50hz motor? 11)whats is the formula for kw, ohm's law 12)if a 3phase motor is rated 3kw,415vac,what is it's rated ampere?

0 Answers  

Whis machine is having higher efficiency Transformer or Generator

2 Answers  

Which of the following statements is incorrect?(a) 1N = 1 kgm/s2(b) 1V = 1 J/C(c) 30mA = 0.03A(d) 1 J = 1N/m

1 Answers  

why CFL lamp requires less electricity than a normal lamp?/

3 Answers  

What is the difference between rated and maximum speed of 3phase induction motor.....? Can the motor speed exceeds the rated speed..?

1 Answers  

What is the armature mmf in a D.C machine?

0 Answers   HPCL,

How to decide the size of the capacitor for a single phase induction motor say 2 HP ??

0 Answers  

explain working principle of earth leakage relay

0 Answers   Divis Laboratories, SMIORE,

In star delta Schematic can we connect OLR in delta circuit

2 Answers   ABB, Lanco,

Why we use two wattmeter during block rotor test and no load test of 3phase induction motor? And how can we understand the neat power requirement of from this test?

2 Answers  

Difference between Lugs and Thimbles

0 Answers   ABB,