Answer / ram krishan singh

gear is a toothed wheel, which is used for transmit power

Answer / harish

Gear is a power transmission device

Answer / kkumar

Gear is a mechanical device to transmit the torque by
varying the speed ration. Some time it can be use to
transmit the same amount of torque and speed also.

Answer / karthick

a gear is power transmission element which is mainly used
to transmit power between two shafts which are either
intersecting or non-intersecting,parallel or non-parallel

Answer / vishwakarma

first of all gears are higher pair mechanism
use to transmit power from one shaft to other
with minimum losses
it has ability to transmit constant velocity ratio

Answer / jayaa

gear is a toothed wheel, which is used for transmit power &
motion between two shaft. it is friction drive

Answer / pravin

Gear is machamicl devic and it,s are use transmission of
power and torqe varying the speed ratio, with out friction
and sllipag . it,s are transmit torqe one shoft to another
shoft same speed and torqe less noise. so it,s are vary
useful diwise for short distans torqe transmision .

Answer / manojjadhav

gear is intersting mechanical devise which transmits power
from one rotating shaft to the other by incrasing torque &
gets desired rpm that u wants....

In a class, there are 15 boys and 10 girls. Three students are selected at random. The probability that 1 girl and 2 boys are selected, is:

2 Answers  

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   CSPDCL-Chhattisgarh State Power Distribution Company Limited, RRB,

In convection heat transfer, if heat flux intensity is doubled then temperature

0 Answers  

what is the pattern of written test for the post of trainee mechanical engg.

0 Answers   IOCL,

In a boiler Natural gas flow 10,000 N cubic meter and combustion air flow 22,000 cubic meter, how I convert gas flow N cubic meter to cubic meter to maintain fuel air ratio? Thank you. ashekullah

3 Answers  

What is the impulse reaction turbine?

0 Answers  

what is entropy acc to new concept?//

1 Answers   L&T, MAHINDRA,

WHAT ARE THE QC & QA PROSSES OF PART

1 Answers   Maruti Suzuki,

What is the gear mechanism of lathe machine?

6 Answers   TATA,

what is bms system and how to work it

0 Answers  

if we not carried out B check at mean time in DG set what will be happen?

0 Answers  

what is vacuuming in air conditioning and why we do it.

3 Answers   intex,