In a boiler Natural gas flow 10,000 N cubic meter and
combustion air flow 22,000 cubic meter, how I convert gas
flow N cubic meter to cubic meter to maintain fuel air ratio?
Thank you.
ashekullah
Answers were Sorted based on User's Feedback
Answer / anand swami
u can calculate it by this formula
P1 V1 / T1 = P2 V2 / T2
Where for normal condition pressure is 1 atm and temp
273 k and v1 is known so volume in m3 at any temp T2 and
ppressure P2 we can calculate
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / gopal singh
to convert nm3 to m3 require standard temperature.
suppose st.temp=30'c
then m3= 273+30/273X(nm3).
| Is This Answer Correct ? | 1 Yes | 2 No |
Answer / c.sudhir
Generally the aiAir to fuel ratio will be 1.3.5 , so t
based on the calarafic value of the Fuel the Air ratio is
maintained , so iam here by writing the calcualation part
with Example .
GENERAL CALCULATION
1. Specific steam should be produced per kg of
briquette.
= …………CV…(Calorific value of
Briquette.)…………
Specific Fuel Enthalpy –
Feed water temperature ( or Enthalpy of Feed water )
Exp: = 4200 KCAL/ KG (BRIQUETTS)
(663-62)
= 6.9 kg of steam / Kg of briquette
1kg of briquette = 6.9kg of steam
2. Specific Fuel consumption per actual
Briquett Burned.
= TOTAL STEAM
PRODUCED
TOTAL
BRIQUETTS CONSUMED (OR)
= TOTAL WATER
CONSUMED
TOTAL
BRIQUETTS COMSUMED
Exp: = 13094KG = 3.2 hs of
STEAM
4186 hs
= 17540 Kg = 4.1kg /STEAM
4186kg
Efficiency of Boiler = Actual /
Standard = 4.1/6.9= 0.59x100= 59%
ACTUAL CALCULATION
= STEAM GENERATED (SP ENTHALPY OF STEAM AT Std
Pressure – FEED WATER Temp
CALALARAFIC VAIVE * FUEL CONSUMED (S.F.C)
ExP: = 13094 ( 663-62) = 0.448100 =44%
4200 *4186Reg.,
C.Sudhir
| Is This Answer Correct ? | 1 Yes | 4 No |
if weld join is failed in radiography what is procudure and its penality
HOW IS FATIGUE DIFFERENT FROM STATIC LOADING??
What is the effect of addition of zinc in copper? What is the use of 70/30 brass ?
Which factors influence the type of fracture in failure of a material ?
In 10.00-20 tyre. what is the meaning of .00 ( after10) ?
What is the seal packing gland for turbine?
How to know the bearing number if we know the shaft diameter and RPM?
What are the compressor and types?
why diesel engine does not have spark plug like petrol engine, how ever petrol is better fuel than diesel?
How much is the maximum distance between the impeller wear ring & casing wear ring pump?
What do you treat in high alkalinity of boiler water? What is a feed water pump? What is a Booster pump?
What is the purpose of gravity tank in the stern tube
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)