Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


HOW GENERATING END VOLTAGE LEVEL (6.6 KV/ 10.5 KV/ 11 KV/
13.5 KV) DECIDED IN POWER PLANT. ON WHAT FACTORS THE
GENERATING END VOLTAGE DECIDED, & WHAT IS THE CALCULATION
USED FOR THIS.

Answers were Sorted based on User's Feedback



HOW GENERATING END VOLTAGE LEVEL (6.6 KV/ 10.5 KV/ 11 KV/ 13.5 KV) DECIDED IN POWER PLANT. ON WHAT..

Answer / raman jain

The generating end voltages are solely decided by the MVA
capacity of generator and cost. for example 250MVA
generator the generating voltage is 16.5 kV but when we go
for 500 MW generator it is 21 kV. If you try to make the
voltage level 16.5 kV for 500 MW generator , the size of
the generator becomes very much large abd very difficult to
transport and costly. on the other hand if you try to use
21 kV voltage generation for 250 MW generators the cost
will increase due the insulation level you are providing.
So it optimse by the designer .

Is This Answer Correct ?    40 Yes 9 No

HOW GENERATING END VOLTAGE LEVEL (6.6 KV/ 10.5 KV/ 11 KV/ 13.5 KV) DECIDED IN POWER PLANT. ON WHAT..

Answer / sumit

generating voltage depends on the power (kva or mva).if
power is incresed voltage will be increased also.by
increasing the voltage we can reduce the current &
conductor size .if cndctr size will be reduce cost reduce
also.

Is This Answer Correct ?    6 Yes 2 No

HOW GENERATING END VOLTAGE LEVEL (6.6 KV/ 10.5 KV/ 11 KV/ 13.5 KV) DECIDED IN POWER PLANT. ON WHAT..

Answer / vipul tayal

it is simply due to FORM FACTOR becoz form factor for a
pure sine wave is 1.11 and in all systems whether 1 phase
or 3 phase it will be a multiple of 1.11 and leads to
voltages like 11,6.6,10.5,11 kv) etc.

Is This Answer Correct ?    24 Yes 26 No

Post New Answer

More Electrical Engineering Interview Questions

why HT motors are earthed only at equipment side & for it's single core cable with aluminium wire armoure using?

1 Answers   Legrand, NLC Neyveli Lignite Corporation Limited,


State the difference between Surge Arrester and Lightning arrester,Both are same or not?

7 Answers  


why generation of electricity in low value voltage

3 Answers  


How to work definite,over pluxing,revers power,OSR relay

0 Answers   Ford,


what is a pilot wiring and whys that called a pilot wiers

0 Answers  


What does the temperature (30 deg or 35 deg celcius) mark on conservator of transformer indicates?

2 Answers   MahaGenco,


How can determine cable size with respect to cable length and area in mm2

1 Answers  


why are we maintaining some specific gravity in battery ?

5 Answers  


Differentiate between low pass, high pass and band pass filter?

0 Answers  


What would be the steps and parameters in case if a fault occurs in transmission line at a distance far from the generating station?

0 Answers  


How power factor of a transformer is calculated

3 Answers  


How to control motor gearbox speed and friquency? If length of cable and dia given, how to measure the voltage drop?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)