Answer / usha sharma

form factor of alternating current is 1.1, which is the
ratio of rms value to average value of alternating current.
so generation of ac is in multiple of11, like
11kv,22kv,33kv,44kv etc

Answer / ishaan

The value of form factor is 1.1 which is calculated for the
sine wave. At this value of form factor, leakage flux is
minimum and efficiency is maximum for any electrical
machines. These machines are operated at sine waves.

Answer / saran.then

because the form factor=rms value/average value.so, for
factor is 1.1 .so the rating is always multiple of 11

Answer / remo

At the time of generation there are many type of losses
therefore earlier use to write 10(+/- 1%)kv so thats why we
generally use to write it as 11kv.Since our ancestral make it
a standard of 11kv,33kv,66kv and as the year pass,many
engineers added a new myth of form factor,10% loss of actual
power.....and thus it make us to suffer a lot.
Since there is 230kv and still like 765kv which are not
multiple of 11.
and production in 11kv and 33kv is more ecnomical

Answer / susanta kumar behera

we know that the form factor is the ratio r m s value
to average value which result is 1.1 so ht voltage
rating is multiply of 11.

Answer / piyush

Production of power in 10KV is more economical than 11kv dear REMO

Answer / anand.k

if 1.11 form factor is reason thnt what about 230v
400v ..............

Answer / james

its not a joke.FF is the exact answer for 11 multiples but
we can also get different voltages by tappings in the
transformer secondary.

Answer / muneeb ahmad

it seems that it is due to form factor but Actually it is
not due to form factor,if there is necessarily multiple of
11 then how can we get 400,127 or etc etc....

i think by changing factors and certain conditions it is
possible to minor change in form factor then how we are
getting same form factor since the production of
electricity....

it is just a misconception of introduction of form factor....

Answer / sss

because naveen kumar's luckey number is 11,that's way HT
voltage is multiple by 11.there is no role in ff(=RMS
value/avg value)1.1

what you mean swtchgear(electrical)

1 Answers  

why we have to do tan delta test of the transformer oil???

5 Answers  

why we use 11 kv 22 kv and so on ?

1 Answers   Air Force,

what purpose to use excaiter in DG.?

0 Answers   TATA,

from 33kv to 440v 2mva transformer how much full load current will be at ht side and lt side and which range of ctpt will be used?

1 Answers  

Why we transmit the power at the voltage in the multiple of 11 or 1.1 like 11kv, 22kv, 66kv, 132kv...... some one told me that it is due to fomr factor 1.1 of sine wave. its fine but while transforming we can choose any voltage, so why only multiple of 1.1 there also.......? plz tell me.

7 Answers  

Difference between directional over current and non directional over current ?

2 Answers  

Hi Everyone ! My Name is Hakim ullah khan please i need formula of Cable Rating because i want to calculate by self without check any Table Chart... Thank you.....

0 Answers  

how to size H.T & L.T Panel ?

0 Answers   Schneider,

WHAT IS AIR GAP VALUE IN MM FOR A 11KV BUSHING OF 11KV/440V DISTRIBUTION TRANSFORMER. AND AIR GAP VALUE OF 25 KV BUSHING OF AT TRANSFORMER OF 25 KV TRACTION. WHAT IS THE CALCULATION FOR THE AIR GAP PERMITTED FOR BUSHINGS AT DIFFERENT VOLTAGES.

0 Answers  

What is the technical formula to calculate the load taken by a motor in Amperes ?

2 Answers  

How can get electrical "c" licence.I am complited in Deee.Passing year of 1993.Working in pvt cocern lt Line.Please advise me .Cell no 9994786021

59 Answers   Apollo Power, Chemplast, Christy Quality Foods, ITI, Mani Associates, Microtech Engineering, TAFE, Tamil Nadu Power Company, TechSun Energies, Thermax,