define jig and fixure?what is diference between jig and
fixure?
Answers were Sorted based on User's Feedback
Answer / maswood ahmed
JIGS:
Jigs are used to hold the work peice and also to guide the
tool while performing the operation.
Jigs are mostly used for dilling operation
FIXTURES:
Fixtures are used only to hold the workpeice and it wont
guide the tool.
Fixtures are mostly used for milling operation
| Is This Answer Correct ? | 139 Yes | 10 No |
Answer / phani
fixture means which can hold the work piece
jig means which can guide the tool bit
| Is This Answer Correct ? | 99 Yes | 17 No |
jig & fixture are the tools used to fasten the productivity
rate by reducing the time of setting the w/p everytime
jigs-used to hold the w/p & guide the drill bit
fixture-used to hold the w/p ,it does not guide the w/p
| Is This Answer Correct ? | 38 Yes | 5 No |
besides holding work jig can guide the tool
| Is This Answer Correct ? | 39 Yes | 8 No |
Answer / k.sivakumar
jigs may be used to hold work piece and guiding the tool in
operation. but fixure only to hold the workpiece alone.
| Is This Answer Correct ? | 36 Yes | 8 No |
Answer / om
A jig is a device used in metal fabrication to do
repetitive assemblies.With the aid of a jig,semiskilled
personnel can do compicated assemblies guided by the jig
A fixture is mainly a device used as a restraint during an
operation.It holds the work piece in position for safe
operation e.g during welding,drilling,milling,etc
| Is This Answer Correct ? | 21 Yes | 5 No |
Answer / tom muckian
A jig is an Irish tune in 6/8 or 9/8 time. A fixture is
something that's always there, like your wife. (Thanks to
all who answered this question because it has haunted me
for 40 years).
| Is This Answer Correct ? | 13 Yes | 5 No |
Answer / nikhil
jig used to hold the work piece and also guide the tool.
fixture only hold the work piece.....
| Is This Answer Correct ? | 8 Yes | 2 No |
Answer / asish ranjan sethi
jig is a penish and fixure is a vegina .and the product of
the combination is a small and a cute child.
| Is This Answer Correct ? | 10 Yes | 5 No |
Answer / arun kumar
A jig is used to guide the tool.
A fixture is used to hold the work piece.
A jig can be used as a guiding tool as well as a fixture,
whereas as a fixture is only used to hold the wok.
| Is This Answer Correct ? | 10 Yes | 6 No |
Air is a bad conductor of heat.why it becomes hot in summer?
What is the vane diagram in centrifugal pump
2 Answers Birla Cement, ITC Infotech,
what is critical temprature discuss that is any pressure greater than critical pressure is valid for boiler design.....2 in what cycle steam power plant is based draw h-s diagram.different process to make gear what is tooth profile what is generatic and directric and many more as i m doing mtech thats why interview was of 30 minute...........
What are to be checked in an induction motor?
What is a slined joint?
Please informe me about bearing e.g ball bearing, what is meaning of number apearing in bearing or bearing housing. for example:- 6305 or UC P 206
a compressor running at 100 rpm gives 40% efficincy speed increase from 200 wt will be the efficincy???????????
Which parameter remains constant in a throttling process ?
WHY MECHANICAL ENGG ARE RECRUTED IN IT COMAPNIES?
In Feature How use in distel water in use in bike.? 2) Above 2020 petrol prise 100 per/lit.? how can use in Poor people in Bike.
why piston is cylindrical in shape
7 Answers Clarion Technologies, Olam International,
What is the cold side of the refrigeration system?
Civil Engineering (5086)
Mechanical Engineering (4453)
Electrical Engineering (16638)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)