Answer / surya

in static routing all routes need toi entered manually in
routers routing table if any changes needs to be done
Network admin have to update the same in routing table.
Dynamic using routing protocols routing changes will be
updated in routers routing table.

Answer / latha

STATIC ROUTING

Static routing is not really a protocol, simply the process
of manually entering routes into the routing table via a
configuration file that is loaded when the routing device
starts up. As an alternative, these routes can be enterd by
a network administrator who configures the routes. Since
these routes don't change after they are configured (unless
a human changes them) they are called 'static' routes.


DYNAMIC ROUTING
Dynamic routing protocols are software applications that
dynamically discover network destinations and how to get to
them.

Answer / ashutosh gupta

In static Routing administrator is responcible to
configuring routing table and if any change
occured,Administrator have to update in routing table
manually, Whereas in Dynamic routing routing table is
updated and maintained by routing protocols such as
RIP,RIPv2,IGRP,EIGRP,OSPF etc

Answer / yogesh vats

static routing is not a protocol this is a simple process
for intering the routers in routing table via a
configuration file that is loaded when routing device
starts-up unless dynemic routing is a software application
that that dynemically discover network destination

Answer / ashutosh

static routing is not a protocol this is a simple process
for intering the routers in routing table via a
configuration file that is loaded when routing device
starts-up unless dynemic routing is a software application
that that dynemically discover network destination

Answer / sudip

static routing is manually entering the route for
destination network where i want to reach. No routing
protocol is required for run it. But whenever any update is
require u have to put it manually.
Dynamic routing is nothing else, just is a protocol which
decided the best destination path based on the routing
decision. Any update is automattically adjust with the
table.

Answer / avinash

Static Routing:
A router with manually configured routing tables is
known as a static router. A network administrator, with
knowledge of the internetwork topology, manually builds and
updates the routing table, programming all routes in the
routing table. Static routers can work well for small
internetworks but do not scale well to large or dynamically
changing internetworks due to their manual administration.

Static routers are not fault tolerant. The lifetime of a
manually configured static route is infinite and, therefore,
static routers do not sense and recover from downed routers
or downed links.

Dynamic Routing

A router with dynamically configured routing tables is
known as a dynamic router. Dynamic routing consists of
routing tables that are built and maintained automatically
through an ongoing communication between routers. This
communication is facilitated by a routing protocol, a series
of periodic or on-demand messages containing routing
information that is exchanged between routers. Except for
their initial configuration, dynamic routers require little
ongoing maintenance, and therefore can scale to larger
internetworks.

Answer / ravikumar

static roting: static routing is not a protocol application and its only a process of updating routing table manually and if any changes is occurred means change the routing table manually.
whereas
Dynamic routing: Dynamic routing is a protocol application and
update the routing table value automatically through the route discovery mechanism.

Answer / rohi

Manually Configured Ip is Static (If you don't have a DHCP
server in your network).
Automatically gained by system throuugh DHCP server is
called Dynamic (DHCP related services must be enabled in ur
services console)

Answer / oliver152

paCkYou all

find the net id and host id of the following IPV4 117.34.3.8 and 132.57.8.6

0 Answers   Green University of Bangladesh,

I HAVE GOT 55% IN 12TH CLASS. IS IT GOOD TO DO B.E. CAN I SIT IN THE CAMPUS SELECTION.

3 Answers   Infosys,

The factorial of a nonnegative integer n is written n! (pronounced “n factorial”) and is defined as follows: n! = n · (n - 1) · (n - 2) · … · 1 (for values of n greater than to 1) and n! = 1 (for n = 0 or n = 1). For example, 5! = 5 · 4 · 3 · 2 · 1, which is 120. Use while structures in each of the following: a) Write a program that reads a nonnegative integer and computes and prints its factorial. Use the following function prototype to calculate factorial: int myFactorial(int n); b) Write a program that estimates the value of the mathematical constant e by using the formula: Use the following function prototype to calculate e: double myE( ); Hint: Use an accuracy of 10 terms. c) Write a program that computes the value of ex by using the formula Use the following function prototype to calculate e: double myEx(int x);

2 Answers  

A. Compare the advantages and disadvantages of a three- dimensional monitor using a varifocal mirror with a stereoscopic system. B. Write a routine to implement the polymarker function.

1 Answers  

Which of the following statements are true about constructors and methods? 1)A constructor has it's own name, a return type and is invoked using the new operator. 2)A function has it's own name, a return type and is invoked using the dot operator. 3)A constructor has the name of the class, no return type and is invoked using the new operator.

4 Answers   CSE,

In HSE what is Lost time accident? why it is to be reported within 48 hrs to gov.authorities ?

0 Answers  

wats the difference between RS latch using NAND n NOR gate? which is to be preffered?

0 Answers   ABC,

What is Landscape in Sap BW?

0 Answers  

write a progremme using function 0f prime no.?

0 Answers  

T is a tree and V is a vertex of T of maximum degree in T, say the degree of V in n. Prove that T has atleast n vertices of degree 1.

0 Answers   TCS,

what is a query for divide a table into two subtable?

0 Answers  

What is CRC? the material will be used in electrical stampings.

0 Answers