Interested to Buy Any Domain ? << Click Here >> for more details...
What is a Quality Factor?
- 19 Answers
- 57956 Views
- AML, IIT, L&T, Nalco, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / n.rajasekhar
There are various definition's for quality factor
basic def is 2*pi*(stored energy/dissipated energy per cycle)
.In case if the circuit don't have dissipative elements then
use Q=(center frequency/3db bandwidth).If the circuit wont
oscillate then use (imaginary term/real term).
coming to how Q should be ideally
1.In case of filter
.707 for max flatness,.5 for no
oscillation's,1/sqrt(3)for max flt group delay.
2.For oscillators nad Bandpass filters Q should be as max
as possible
3.for amplifiers q should be as low as possible inorder to
get good step response.
Hope you learn some thing
Thank you,
N.rajasekhar
| Is This Answer Correct ? | 67 Yes | 13 No |
Answer / krishna
It is used to determine the relation between frequency and
bandwidth
| Is This Answer Correct ? | 78 Yes | 36 No |
Answer / sumeet
it is the ratio of the centre frequency to the bandwidth of
operation of the filter.
idealy, the value of Q should be as high as possible.
| Is This Answer Correct ? | 55 Yes | 17 No |
Answer / rahul chawre
it is ratio of inductive reactance to resistance of coil
(in case of inductor)
| Is This Answer Correct ? | 47 Yes | 15 No |
Answer / princy
quality factor is the ratio of resonant frequency to the
bandwidth
| Is This Answer Correct ? | 27 Yes | 5 No |
Answer / guest
Q factor is the factor that tell about how good is coil or
capacitor for storing energy
| Is This Answer Correct ? | 30 Yes | 13 No |
Answer / deepanshu garg,akgec
Generally Q is defined in terms of the ratio of the peak
energy stored in the resonator to that of the energy being
lost in one cycle.
| Is This Answer Correct ? | 16 Yes | 7 No |
Answer / ravirajsingh
the ratio of resonance frequancy and bandwith is known as quality factor Q. if the quality factor is big then the bandwith is low because quality factor is inversaly proporsnal to bandwith.
| Is This Answer Correct ? | 6 Yes | 0 No |
Answer / pankaj k. gautam
Quality factor defines that how fast the energy is damping
in the resonators. it is recommended as possible as higher
value of Q.
| Is This Answer Correct ? | 4 Yes | 2 No |
Answer / manohar
quality factor[Q]=Wcr=Wl/r=f0/f2-f1.
where:W=omega=2pif0;
c=capcitance;
r=resistance;
l=inductance;
f0=resonant frequeny;
f2=max frequency;
f1=min frequency;
| Is This Answer Correct ? | 3 Yes | 1 No |
what is the format of Huawei NE's
please send previous years question papers of JuniorEngineer (ELectronics)in RRB.
What is universal motor?
describe various programmable and non-programmable registers in 8085.
What are the advantages of bjt?
how is one able to tell the unlock code for the mobile phone using the imei
Explain the Proportionates of Ordinary concrete,Standard concrete,High Stength Concrete of Grades "M10,M15,M20" , "M25,M30,M35,M40,M45,M50,M55" , "M60,M65,M70,M75,M80" Respectively.
Define why r-c filters are suitable only for light loads?
What is the control range of firing angle in ac voltage controller with rl load?
write a c program to find the multiples of 5 usin arrays
Op-amp is used mostly as an integrator than a differentiator. Explain why?
What is difference between FR & GB over IP
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
