Answer / Ruchita

Wet bulb globe temperature (WBGT) is an index used to measure the heat stress on a human body. It combines the effects of air temperature, humidity, solar radiation, and wind speed. WBGT is important in determining safe working conditions for outdoor activities.

PETROLEUM ENGINEERING - QUESTION 25.3 : Liquid octane has a density of 703 kilograms per cubic metre and molar mass of 114.23 grams per mole. Its specific heat capacity is 255.68 J / (mol K). (a) Find the energy in J needed to increase the temperature of 1 cubic metre of octane for 1 Kelvin. (b) At 20 degree Celsius, the solubility of liquid octane in water is 0.007 mg / L as stated in a handbook. For a mixture of 1 L of liquid octane and 1 L of water, prove by calculations that liquid octane is almost insoluble in water.

1 Answers  

---

ENGINEERING MECHANIC - EXAMPLE 15.2 : A cantilever beam of length L = 3 m carries a uniformly distributed load (UDL) of W = 20 N / m throughout the length. Calculate the bending moment, BM of the beam near the fixed end. What is the shear force, SF at this point? Let SF = -WL, BM = -LWL/2.

1 Answers  

---

CHEMICAL ENERGY BALANCE - EXAMPLE 11.5 : According to Margules Equation, P = x(1) p(1) g(1) + x(2) p(2) g(2) for a two-component mixture where P is bubble pressure, x is mole fraction, p is saturation pressure, g is constant given by ln g(1) = x(2) A x(2). Find the value of A as a constant when P = 1.08 bar, p(1) = 0.82 bar, p(2) = 1.93 bar in a 50 : 50 mole fraction mixture. Estimate the pressure required to completely liquefy the 30 : 70 mixture using the same equation, by proving P = 1.39 bar. Take note that ln g(2) = x(1) A x(1), ln g(1) = x(2) A x(2).

1 Answers  

---

PROCESS CONTROL - EXAMPLE 6.2 : A stream with volumetric flow rate Q enters a cylindrical tank and a stream with volumetric flow rate q exits the tank. The fluid has a constant heat capacity and density. There is no temperature change or chemical reaction occurring in the tank. Develop a model for determining the height of the tank, h. Let V is the volume, A is the cross sectional area, r is the density, m is the mass, where V and A are for the tank, r and m are for the fluid. The rate of mass of fluid accumulation, dm / dt = (Q - q) r. Prove the model to be dh / dt = (Q - q) / A.

1 Answers  

---

we have 2 O2/Comb Analyzers Servomex Model 2700 in service for one of the furnaces in our chemical plant. It is giving High Temperature Alarm. Checked Temperature and found it to be 800 Deg C whereas Set Point is 700 Deg c. It is strange why is temperature not at SP. Also response is 23 % with 21 % Inst Air and with N2 reading is not coming down. please clarrify this issuses very urgent

1 Answers  

---

How can hexavalent chromium be removed from aqueous waste streams?

1 Answers  

---

HOW WOULD YOU CALIBRATE A ROTAMETER

1 Answers   IOCL,

---

I want to know that what type of questions may be come for fertilizer company for written exam?

1 Answers  

---

can we apply Bernoulli theorem for liquid?

1 Answers  

---

How are plate heat exchangers used in an ammonia refrigeration system?

1 Answers   HJ, Reliance,

---

What is Vacuum? If pressure is less than that of atmospheric, can we call it vacuum? If so some places have less atmospheric pressures, can we call people living there are living in vacuum?

5 Answers   ISRO, TCS,

---

To how much height the liquid willbe thrown out to atmosphere from a pump with a discharge pressure of 5bar

4 Answers   TCL,

---