How to calibration a control valve?


No Answer is Posted For this Question
Be the First to Post Answer

Post New Answer

More Instrumentation Interview Questions

where can we use viberation transmitter,and how can we control viberation?

1 Answers   Maden,


wht is snap action switch?where it is used?is there any diff between snap action switch and normal pressure switch?

1 Answers   ONGC,


Isometric drawings are generated during _________________ phase of a project

0 Answers  


can we use a control valve without positioner

19 Answers  


WHAT IS THE DIFF BETWEEN FREQUENCY AND INTENSITY?HOW IT WORKS IN FLAME SCANNER ?

1 Answers  






while am calibrating Drager polytron 2IR flame gas detector occured non zero status.how can i get zero status?

0 Answers   Gasco,


Actual using of tube bender to bend 2 opposite 90 deg at correct measurement center to center of tubing.

0 Answers   CCIE,


what is meant by Valve reversibility?

2 Answers  


A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

0 Answers   MNC,


how to calibrate control valves & power cylinders & ultra sonic level transmitters

0 Answers   ABB,


Can Any body tell me about the Contact or Email id of any good Consultancy which help me to find a job in Instrumentation Field in India .I have Six years of Work Experience in the Same field.Please revert me back on shammi_gwalior@yahoo.com ?

0 Answers  


Dear sir I am MD.zafar eqbal. I have taken this id from allinterwiev .com I have qustion if you dont mind. 1.what is the maximum operating temprature in instrumentation. 2. I want know about viberation i mean wahat types of sensor used in viberation And what types of trabsmitter used.and hiw to control it and wher is used of viberation transmitter and finally how to control it and what types of fault come. Sorry for disturbing you. I know you have no reason for help me. Because you dont know about me.but i request you please help me these question are very usefull for my feauture.plz sir Thanking you. Sent from Yahoo! Mail on Android

4 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)