Answer / benu

kva=kw/pf,with low pf,kva will be high,insulation cost in generator and transformer+cu loss in transmission line will rise and efficiency will come down

Answer / rajivgandhi

should be reduce the losses ..

Answer / koti

above answer is partially correct i.e, at low pf the kw output is low and is due to inductance and capacitance elements of ckt but not harmonics

Answer / ghulammohyhuddin

power factor control mager demand form electrical city

because actual lode between appearance lode is power factor

Answer / purushottam kumar

for constant power and terminal voltage ,if power factor is low current drawn is more ,so more lose ocour ,regulation is poor, conductor size increased than with high power factor

Answer / sudhakar g

Power factor is imp bcoz....ex: If we have an panel that
will give the o/p of 300KW but if we dont maintain the
powerfactor by using APFCR it will give the o/p of 240KW
only....by maintain the powerfactor by using the APFCR we
can get (0.98%)....power factor means something lagging and
leading in power due to harmonics...

As load in a transformer increases, mutual flux linkage in core= A increases B decreases C not change D first increase then decrease

2 Answers  

What type of DC Generator is used for Arc Welding purposes?

7 Answers   CPCL, Rubicon,

When one of three series resistors is removed from a circuit and the circuit is reconnected, the current

1 Answers  

Why we check only first column of root locus..?

1 Answers   IES,

relation between power station capacity and voltage level?

0 Answers  

Why Capacitor & ignator used in MH lamp

2 Answers   Bell,

How the starter control the starting current in three phase AC Motor?(In DC apply the reistance).

6 Answers  

On what principle reluctance motors work?

1 Answers  

why the auxilary(starting)winding is provided in single phase inductoin motor?

5 Answers  

at which voltage level arcing ground is occurs ??????????

0 Answers   TATA,

what is kondo syatem in eletrical traction

0 Answers   APCPDCL,

How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9

0 Answers