What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/

What will be the effect of in HT XLPE 220 KV
cable when one side of the Armour/cable ends are not
grounded. Will there is difference between 3-phase voltages?
like: if
A. Both End of Cable grounded Phase Voltages:- V1=219 KV,
v2=220 Kv, v3=220 KV.
B. One End is grounded other is not: than Impact on Phase
Voltages:- V1= KV, v2= Kv, v3= KV. Remain same or
unchanged??

Question Posted / mahendar kumar

3 Answers
6015 Views
Jamshoro, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/cable ends are not ..

Answer / hemant

mostly we consider that armour is given for machanical
protection to cable from any type of hard punching on cable
and other if cable get damaged then it touch to armour
which alredy connected to ground hence our differantial
reley get pick up and device which connect to ht cable is
protected. if both end of armour is connected to ground
there may not any effect to supply voltage in cable it
depend upon cable insulation. only leakage current get
discharge via armour to ground. hence in point of me trere
is no one effect on 3 phase voltage it also remain same.
one thing is that armour one end require to connect ground
and second to device for earthing to device.

Is This Answer Correct ?

2 Yes

1 No

What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/cable ends are not ..

Answer / mahendar kumar

In my opinion Phase voltage would be affected due ungrounded
one end cable.

Is This Answer Correct ?

2 Yes

2 No

What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/cable ends are not ..

Answer / k.prakashchandra

You have measured voltages with the help of PTs located near
the earthed cable ends . As there is a slight difference in
capacitances of the three cables to the Armour(probably due
to unequal lengths) and impedance of the PT is higher than
that of capacitance of the cable ,the neutral is decided by
the capacitances.There is no difference in actual voltages
but there will be a slight difference in measured voltages

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

Please give me a ansver for why currant transforme noe point should erthing

1 Answers

Why HT motor of 3.3 kw or 6.6 KV, one side foundation ( mostly non drive end ) keep insulated from ground ?

2 Answers

what is difference between 9kv 5ka surge arrester and 9kv 10ka surge arrester.

1 Answers Voltamp,

what are balanced and unbalanced loads

1 Answers GGH,

I need bhel electrical test pattern & paper

0 Answers

3 pahase 750kva Running 2 DG sets in 35 mints.525ampers. and 616 kw how much fuel consumption in Generator.what is the formula.

1 Answers Delite Systems Engineering,

what's burden resistor, why it's used?

1 Answers Bhel, TVS Group,

how rated the neutral voltage of transformer and reactor, e.g. 400/220, 200MVA transformer have neutral voltage of 33kv. and reactor voltage 145kv. how this rating decided?

1 Answers MEIL,

why we use bare wire in high tension power instead of using insulated wire?

2 Answers

What is the use of insulation tester and how it is to be used.

2 Answers

what is the reqirred voltage in HT motor to get full RPM on no load test?

1 Answers

how many amps in 1KVA?

16 Answers TATA,

For more Electrical Engineering Interview Questions Click Here