Can I use 1 phase power supply to run 3 phase motor? If yes, how?

Answers were Sorted based on User's Feedback



Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / jay

It is possible.

We can give the parallel connection through single phase line by using capacitance.

Is This Answer Correct ?    0 Yes 0 No

Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / sunil shirole

Some time can be used in low rating/torque motors through VFD

Is This Answer Correct ?    0 Yes 1 No

Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / princess

Yes we can use single phase supply but the motor will run at reduced speed just like single phase induction motor

Is This Answer Correct ?    0 Yes 1 No

Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / basith

it is possible dear.but we cannot use for permanent. we can use for temporally.

Is This Answer Correct ?    0 Yes 1 No

Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / kish

Yes it is possible. 6
terminals in motor
terminal. Put 3 terminals
for star connection and
other 3 terminals give
fan connection. Kishore.

Is This Answer Correct ?    0 Yes 3 No

Can I use 1 phase power supply to run 3 phase motor? If yes, how?..

Answer / konner tanmay

it is not possible.

Is This Answer Correct ?    0 Yes 6 No

Post New Answer

More Electrical Engineering Interview Questions

Why DC exitation to AC Generator? Why not AC?

2 Answers   Equate,


1.two coupled coils with L1=L2=0.6 H have a coupling coefficient of k=0.8 the turns ratio N1/N2 is......

5 Answers   BSNL, SSC,


In a d.c circuit, if current and resistance are known, power (P=I*I*R) can be determined. This relationship also applied to an a.c circuit. Comment the reason for this.

3 Answers  


If we connect the capacitor banks for DG set for maintainig the power factor, it will effect to alternator windings??????????

7 Answers  


Why synchronous motor is used in power factor improvement,dc series in lift

0 Answers  






Why is shaft current insulation required on large motors & when should it be checked i.e. before or after assembly?

2 Answers   Aramco,


how can we calculate the cooper armed cable size if the protection load of main fuse is 80 ampere.

1 Answers  


what are the main Parts of VCB

1 Answers  


what are the factors to be considered while design the breaker either HT or LT??

0 Answers  


lorteny method

0 Answers  


The inventer is a battery, but if lost current at home u will turn on the fan but the is AC and inventer battery is dc . Then how the fan was rotating. What device Or machine in fan converst the Dc power to Ac power

0 Answers  


can you tell me/show me, how to manually synchronize 2 DG. preferred with video.

2 Answers   Cummins,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)