what is the reason of power development in synchronous
generator due to saliency ?



what is the reason of power development in synchronous generator due to saliency ?..

Answer / brahma reddy

the power exp for syn. gen due to saliency is

P= (EV/Xd)sin& + v2/2[1/Xd-1/Xq]sin2&

the term after + is called reluctance power that
means eventhough gen not starts it will posses some power
due its reluctance
due to this in syn gen powrer is saliency

Is This Answer Correct ?    4 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

what are the tests comes under the type test, what tests comes under routine tests.

0 Answers  


is it possible for different brand of H.V transformers to run or operate in parallel to each other? if so how much disturbance can this affact the H.V bus bar?

0 Answers   Unitech,


What is negative sequence over voltage element?

0 Answers   Green T&D,


what are advantage and disadvantage of zener diode?

2 Answers   Infosys,


Ash AAAC conductor is used for which KV lines

1 Answers  






some meggers have three terminals. wat is the real function of the earth terminal?

2 Answers  


How many types of relay are present in a VCB and ACB, what are the tests we can conduct on both breakers and how to set the relays values

2 Answers   Hyundai, Sodexo,


A cotter joint is generally used to transmit

0 Answers   Caterpillar,


Is it posssible to obtain the higher speed(3000rpm) for adiferentiallly cascaded induction motors(with 8 and 6 poles)

3 Answers  


I have a question, I visit 01 site and face a problem, there is 2.5 ton Air Con working, when air con compressor is running at that time rectifier voltages are increasing upto 290-295 v and rectifier is giving main high alarm (rectifier is APC single phase), before starting compressor rectifier voltages was 230v. when air con is going off rectifier voltages are decreasing smoothly at its actual voltages 230v. Load on Genset phases is this: Red-13.5 amp AC (Air Con load), Yellow-1.7 amp AC (BTS lights etc.) and Blew-4 amp AC (telecom system load), Genset phase to phase and neutral to phase voltages are also ok. These are 10 sites having same system and same rectifier APC brand at every site 02 genset are working but the problem is same at all these 10 sites. What will be the reason behind???

1 Answers  


what will happen if u run induction motor beyond its rated speed

13 Answers   Adani, BARC, Bescom,


what is the size of ht cable of 33kv ht line and transformers ratings are 1 Mva and 5mva.please send formula also.

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)