What is the lap length in your project?

Categories >> Engineering >> Civil Engineering
Suggest New Category

Question Posted / sanjay kumar

11 Answers
21650 Views
L&T, Practical Viva Questions, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is the lap length in your project?..

Answer / basirul islam

The length of Lap in tension Reinforcement = 50D
Compression reinforcement=40D

Is This Answer Correct ?

12 Yes

1 No

What is the lap length in your project?..

Answer / shalu verma

40 TO 50D
WHERE,
D= DIA OF BAR

Is This Answer Correct ?

7 Yes

0 No

What is the lap length in your project?..

Answer / rethina kumar

any grade , any bar, procedure or not change .

for r.c.c column , beams , (50d) d is diameter of bar )

Is This Answer Correct ?

11 Yes

5 No

What is the lap length in your project?..

Answer / sanjay kumar

we are using 52d lap length.

Is This Answer Correct ?

6 Yes

4 No

What is the lap length in your project?..

Answer / sathesh .b.nama

AS PER IS:456 ITS MENTIONED IN TENSION ZONE 30 DIA OF BAR & IN COMPRESSION ZONE ITZ 24 DIA OF BAR..

Is This Answer Correct ?

3 Yes

1 No

What is the lap length in your project?..

Answer / vedbyas kumar

result of lap length is
50D(dia of bar)
such as 50*16=800mm
50*12=600mm

Is This Answer Correct ?

2 Yes

1 No

What is the lap length in your project?..

Answer / yash kumar

lap length in tension as well as in compression zone it as standerdly taken max=50d,min-40d,d is dia of bar.and if there is welded joint preference lap is different

Is This Answer Correct ?

1 Yes

0 No

What is the lap length in your project?..

Answer / mantu

48D IN TENSION AND 40D IN COMPRESSION ZONE

Is This Answer Correct ?

2 Yes

2 No

What is the lap length in your project?..

Answer / pandu

as per IS456 the overlap length should not be more than L/
50(mm). L=length

Is This Answer Correct ?

2 Yes

3 No

What is the lap length in your project?..

Answer / selvakumar

We are ushing 40d lab length

Is This Answer Correct ?

5 Yes

9 No

Post New Answer

More Civil Engineering Interview Questions

whats is difference between anchorage length and development length

1 Answers

how much quantity of cement,sand and water required for 1 sq feet flooring work .

1 Answers JMD Group,

what is the safe bearing capacity of hard murum? can we consider it 50 ton?m2

1 Answers

what is a mix design GSB and WMM

5 Answers Maharashtra Industrial Development Corporation MIDC,

how to calculate the density of cement and how can we convert no. of Kgs of cement to Metric tonnes??

2 Answers

1 cum brick work CM1:6 how many bricks sand cement required brick size 8"4"3"

3 Answers

Is it possible to make a feature using an overdefined sketch?

1 Answers

whether earth to the height of 80cm could be filled in the basement inm place of jamuna sand

5 Answers L&T,

how gradation of aggregates effect on slump of fresh concrete?

1 Answers

what is escalation?how it is done?

1 Answers Vishal Nirmiti,

What are the causes of building collapse?

1 Answers

1 Cubic Meter = 487 Modular Brick, 1 Cubic Meter = 494 Non Modular Brick, (As per Rate Analysis DSR 2012 Vol.-1)what is the Brick Size ? 1 Cubic Feet = 13 Modular Brick, 1 Cubic Feet = 17 Non Modular Brick. what is the Brick Size ?

2 Answers ABR Constructions,

For more Civil Engineering Interview Questions Click Here