Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


why does cooling chamber used in a gas turbine? why can't we
use exhaust hot air in the compressor?

Answers were Sorted based on User's Feedback



why does cooling chamber used in a gas turbine? why can't we use exhaust hot air in the compre..

Answer / azhar iqbal

cooling chamber is used in the turbine to control it's
exhaust temperature and in this way to increase it's
efficiency by 2-3% almost.
Also it is used to protect the damaging of the turbine
blades as high temperature currents flow upon them after
combustion.

Is This Answer Correct ?    7 Yes 1 No

why does cooling chamber used in a gas turbine? why can't we use exhaust hot air in the compre..

Answer / osanandkumar

it used to dissipate or to maintain the specified
temperature of the turbine

Is This Answer Correct ?    5 Yes 2 No

why does cooling chamber used in a gas turbine? why can't we use exhaust hot air in the compre..

Answer / visu

in a compressor blade material uses for cooled air
only...not for hot air..

Is This Answer Correct ?    1 Yes 0 No

why does cooling chamber used in a gas turbine? why can't we use exhaust hot air in the compre..

Answer / eng.walid rezk

the compressor cannot work with the exhaust air
because if we do that the area under the curve of p-v
diagram will increase it is input work on an open system so
it equal -pdv as you must know so the area increases this
mean as well the work required increases and the over all
efficiency will decrease as well so in the two stage
compression cycle we had to make a water inter cooler to
reduce the work consumption

Is This Answer Correct ?    1 Yes 0 No

Post New Answer



More Mechanical Engineering Interview Questions

min work in a compresor is possible when the value of adiabatic index n is equal to a).75 b)1 c)1.27 d)1.35 e)2 what is adiabatic index.

1 Answers  


How can heat be applied to acrylic?

0 Answers  


what are the parameters are selected while manufacturing a single cylinder block?what are the different kind of test is conducted on it so that it can withstand with all those condition which required to run the engine efficiently.which force is act when piston slide inside the cylinder.

0 Answers  


what are your negative points?

3 Answers  


A very strange fault i cam across today,that i never experienced not studied before, i need an answer for this. Phase to phase or line to line , L1,L2 & L3, voltages are 490VAC, but if i use line to ground , its again 490 VAC. . . whats the fault and theory behind of it?

0 Answers  






why water's critical point is 4*c ?

4 Answers   Essar,


Name the refrigerant that is used on domestic refrigerators?

7 Answers  


How much is the maximum distance between the impeller wear ring & casing wear ring pump?

0 Answers   Power Plant,


What is the most important, or helpful,project that you have contributed to?

0 Answers  


The capacity of a domestic refrigerator is in the range of ?

0 Answers  


what is vacuuming in air conditioning and why we do it.

3 Answers   intex,


22216 CC bearing

0 Answers  






Categories
  • Civil Engineering Interview Questions Civil Engineering (5076)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4445)
  • Electrical Engineering Interview Questions Electrical Engineering (16606)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2992)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1378)