Answer / pradhyumn

OTI stands for Oil Temperature Indicator and WTI stands for
Winding Temperature Indicator. They are used for
Transformer protection.The temperature of winding increases
as the load increases. Oil is used as coolant for the
winding so as winding heats up oil temp. rises as well.
The life of transformer depends on insulating material
between the windings so it is important to check and
control the temp. OTI and WTI are thus used for alarm or
tripping of the transformers.

Answer / rizwan

A basic or Avg Difference in OTI & WTI are, :- WTI needs a
CT to function , While OTI does not need a CT. WTI has both
Alarm & Trip , Though OTI also has both ALarm & Trip , there
is also a OTI without Alarm & Trip . Its not the cas of WTI.

Answer / kolhe g j

10 Degree Centigrade

Answer / c.d.elkunchwar

There is no fix differnce as such.Itdepends upon the
transformer tempareture gradiant at that current, specified
by the manufacturer.the difference between ot&wt varies as
per load and gradient.Normally it can be from 12 to 16
degrees at full load.

Answer / k.prakashchandra

The above answer given by me is not true in all cases.Those
were the readings recorded on 220/110 KV auto
transformer.The WT is higher than OT as WTI is close to the
source of heat.The difference between WT and OT depends on
cooling and oil circulation.More the difference worse the
cooling efficiency.The difference is about 20 %(220 KV) to
40% (110KV) of temperature rise in WT ,as observed in case
of the above Tr.But WT of tertiary was found to be less than
the OT

Answer / k.prakashchandra

3-15 degree C

Answer / boss

it was correct answar, but ct current rating has been deppond on trasformer manufacture.

Double Busbar Scheme for outdoor switch yard system (132kv) step up power plant Hi friends 1. in this system both busbars energized all the time. 2. what is the meaning of main BB and transfer BB, 3. step up transformer connect main bus bar all the time or both BB connected through DS switch . 4.bus sectionalization means ? thank you.

1 Answers   ABC, Gael,

Why do u join toreent power ?

1 Answers  

what are the needs of electrical earthing.... other than protection?

5 Answers   Eskom,

slipring induction motor starting time Lrs operating why lrs starting time lrs outer body didn't get shock

0 Answers   Ramco,

what is the difference b/w neutral and earth?what is the need of earthing and what are the different methods for earthing?

4 Answers   NTPC,

Hello every one I am currently working in IT side but i have an offer to work under 'A' license holder and he says i can get c license what is the use of c license and what shall i do after getting it basically i am an electrical graduate please help me shall i leave this it job and work in electrical maintenance will i have a good future i am confused Thank You in Advance

1 Answers  

What is encoder, how it function

9 Answers   Coca Cola,

which type of material is used for making motor encloser

3 Answers  

campared to ac, in dc corona loss is

4 Answers   DRDO,

what is the use of earthing ?

8 Answers   Electrical Tech,

can anybody give me current carrying capacity of cables e.g size of cable in sq.mm & its current capacity both alluminum & for copper

4 Answers  

my question is that....few days ago i had installed a three phase motor starter for an electric saw.the motor will run and make the hydraulic pressure which will be goes to pressure cylender by up and down lever.two number of limitswitches are also installed on cylinder for safety of motor.now when the arm of cylinder reaches to the upper or lower limit it will cut the motor's line.and motor will be stop.now wana know that what will i do that motor runs continue after the limitswitch cut it down but it shold not be made any pressure.pls answer me in brief.

3 Answers