Why RX LEVEL is Negative in GSM????

Answers were Sorted based on User's Feedback



Why RX LEVEL is Negative in GSM????..

Answer / ankit kankane

because of air attenuation , the RX level is -ve .

we know
P(dbm)= 10 +10 log p(w)

o dbm = 1 mW
-10 dbm= 0.1 mw
-20 dbm =0.01 mw

normally GSM 900 , 1800 we transmit RF in Antenna ,power = 20 to 25 W
depending on Cell sector,

& we receive only <0.01 mw because of AIR attenuation and other external attenuation , we always get the receiving(Mobile set) singal in '-ve' dbm .

Is This Answer Correct ?    36 Yes 5 No

Why RX LEVEL is Negative in GSM????..

Answer / cnu

- 48 volts. This -48 volts is required by the copper wires to
prevent it from corroded & eluded.

Is This Answer Correct ?    9 Yes 44 No

Post New Answer

More Electronics Communications Interview Questions

What is conductance? How is it measured?

0 Answers  


What are measurement reports in TEMS tools?

0 Answers  


hi i m an EC engg i had cleared written test for PE for BEL plz help be for interview provide me full information about intrvw as much as u can.. thankx..

14 Answers   BEL, NTPC, ZTE,


How many maximum PWSA cards can be inserted in a Ultra BTS cabinet How many maximum PWSB cards can be inserted in a Ultra BTS cabinet How many maximum PWSC cards can be inserted in a Ultra BTS cabinet What is the output power rating of one PWSA card What is the output power rating of one PWSB card What is the output power rating of one PWSC card What is the function of Receiver Multicoupler (M2xA or M6xA) How many TRX's are supported by one Receiver Multicoupler- M2xA How many TRX's are supported by one Receiver Multicoupler- M6xA What is the function of Remote Tune Combiner (RTxx) unit The FIU19(E) units main LED is red. What is the meaning?

0 Answers   NSN,


Why the width of the base region of a transistor is kept very small compared to other regions?

0 Answers  






what is the dwdm

7 Answers   DRDO,


what is an industrial electronics engineer ? what he does ? what specialities and experties he should have ? what are the difference between industrial electronics engineer & electronics engineer & electrical engineer ?

0 Answers   TATA,


why a capacitor blocks the DC signal?

2 Answers   Cummins,


what is the name of 1st micro-controller?

1 Answers  


What is its magnitude for ge and si?

0 Answers  


Explain the construction of plasma screens.

0 Answers  


Explain what are the two mechanisms of breakdown in a p-n junction?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)