Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


WHY ARE THE LT GENERATORS SOLIDLY EARTHED WHILE THE HT
GENERATORS ARE EARTHE THROUGH NGR OR NGT??

Answers were Sorted based on User's Feedback



WHY ARE THE LT GENERATORS SOLIDLY EARTHED WHILE THE HT GENERATORS ARE EARTHE THROUGH NGR OR NGT??..

Answer / sanjay kolambekar

Small Generator's are usually a low voltage or
highimpedance in case of HV generator with lower rating
hence the fault current will be less and equipments can
withstand the same. Where as in case of HV Generators with
larger ratings the voltage level is high or the impedance
is low hence the fault current is much higheer. In order to
limit the Fault current to the required level suitable
rating of resistance needs to be introduced between the
Generator neutral and Earth.

Is This Answer Correct ?    10 Yes 0 No

WHY ARE THE LT GENERATORS SOLIDLY EARTHED WHILE THE HT GENERATORS ARE EARTHE THROUGH NGR OR NGT??..

Answer / subash

in HV Generators with larger ratings the voltage level is
high or the impedance is low hence the fault current is
much higheer. In order to limit the Fault current to the
required level suitable rating of resistance needs to be
introduced between the Generator neutral and Earth and to
protect the insulation of the generator and getting heated
up while fault uccurs

Is This Answer Correct ?    4 Yes 0 No

WHY ARE THE LT GENERATORS SOLIDLY EARTHED WHILE THE HT GENERATORS ARE EARTHE THROUGH NGR OR NGT??..

Answer / k.prakashchandra

Electrical energy is directly is utilised in case of small
alternators whereas it is not so in HT generators.

Is This Answer Correct ?    0 Yes 5 No

Post New Answer

More Electrical Engineering Interview Questions

what is physical distance of isolator to VCB in 33/11kv sub stations

0 Answers   Enercon,


why we short ckt the secondry vo5tage/ winding in transfr and motor?

2 Answers  


can anyone explain the star-delta motor control wiring ,which wire go where and how they operate?

0 Answers  


what are the tests comes under the type test, what tests comes under routine tests.

0 Answers  


my question is that....few days ago i had installed a three phase motor starter for an electric saw.the motor will run and make the hydraulic pressure which will be goes to pressure cylender by up and down lever.two number of limitswitches are also installed on cylinder for safety of motor.now when the arm of cylinder reaches to the upper or lower limit it will cut the motor's line.and motor will be stop.now wana know that what will i do that motor runs continue after the limitswitch cut it down but it shold not be made any pressure.pls answer me in brief.

3 Answers  


what is MULTIPLYING FACTOR in substations??

2 Answers  


what kinds of Transformer oil grade is better for power transformer ?

0 Answers   KSRM Steel Plant,


Define motor & pump?

3 Answers  


bitumar

0 Answers   Bhel,


i alternator which of genarator used for excitor the what is reason?

3 Answers  


what use can we make of 3rd harmonic component

5 Answers   Bhel, General Motors GM,


How to increase the backup of three phase ups?

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)