Answer / sandeep.h.p

Turbo chargers are used to increase mass flow rate of air
and mainly used to get more fuel combustion
efficiency......

Answer / vivek singh

it increases the pressure of the intake fuel-air mixture...
so the density of the mixture is increased..
as a result of this more mass of air-fuel mixture is
introduced inside the cylinder...
so increasing the power output...

Answer / manisha

o A turbo charger is a device that uses the energy of exhaust gases coming out from an engine to compress the air going into the engine. It must have at least 4 openings: 1 for the engine exhaust gas to enter; a 2nd for the exhaust gas to exit; a 3rd opening for intake air to enter the turbocharger; and a 4th for the intake air to exit the turbo charger on its way to the engine intake. A turbo charger will also have 1 additional opening to vent excess air pressure. Increasing the intake air pressure going into an engine can increase the engine's power, but too much air pressure can damage the engine. Increasing the pressure increases the power of the engine because of the increased density of the air. Increased air density means more oxygen molecules, which means the engine can respond by increasing the amount of fuel it mixes with that oxygen.

Answer / abdul hameed

In high speed enines or the engine operates at high
altitude, the air intake is not sufficient to meet the
compression ratio. Turbocharger is to push more amount of
air in to cylinder to meet compression ratio.

Answer / m.s.sakthiganesh

The purpose of turbocharger is to compress the air flowing
in to the diesel engine this lets the engine squeeze more
air into a cylinder and more air means that more fuel can
be added.The engine burns air and fuel to create mechanical
power the more air and fuel it can burn the more powerful
it is.simply says..
The turbo charger housing is designed to convert "High
velocity Low pressure steam into High pressure low velocity
steam"

Answer / xavier

the function of turbo charger in diesel engine, as we know is to add or to increase the efficiency of air to make a high power combustion in a cylinder as the fuel increase too.

Answer / suraj chhetri

In exhaust gas turbo charging, the exhaust gas energy, which would normally be wasted, is used to drive a turbine. The exhaust gases are diverted so that they drive a small turbine made of a lightweight material; the turbine drives a compressor, which draws in filtered air from the air cleaner and feeds this at a much higher pressure to the engine. This enables more fuel to be birnt with a greayer mass of charged air, thus increasing engine power output. Better air aviliability enhances the combustion process, thus leading to lower fuel consumption and fewer emissions and lower enginr npise and reduced power loss at high altitude...

Answer / priya

Turbocharged main function is it increase the engine efficiency that s with charge the fresh air into the engine.and bring out the born gas at the exhust line..

Answer / abdul haseeb saindak power pla

turbo charger increase volumetric efficiency its means turbo charger pumps double amount of air into the combustion chamber with pressure that increase engine working efficiency 30% to 40%.
FUNCTION;
the turbo charger consists of a turbine and a compressor, assembled in single unit.
the exhaust gas from diesel engine flows through gas inlet casing ,expends in the nozzle ring ,impart energy to the blading of turbine rotor and passes via gas outlet casing and an exhaust pipe into atmosphere.
the air required for diesel engine suction from air filter passes through branch pipe to the inducer and compressor wheel flow through diffuser leaves turbo charger via pressure pipe of the air outlet casing into charge air cooler finely ready for burning into combustion chamber.       

Answer / ankit_kamani2008

to provide extra air for 100% combustion.

why the rail in form of I-beam?

1 Answers  

What is the difference between Michell type bearing and anti friction bearing and the application.

0 Answers   Atomic Energy Commission, DAE,

I am using 500 KVA DG set but I am facing one problem that frequently radiator getting leak what will be the reason?????

0 Answers  

what is accilaration

2 Answers  

Inspection for intermediate shaft bearing.

1 Answers   RRB,

i have been selected for the HAL interview? what type of questions can i expect? technical or personal? pls help me in this regard and mail to sankar_aji@yahoo.co.in

0 Answers   HAL,

IF 125 kva diesel generator generating 13 kw energy in an hour then how much percentage of load is connected to generator and generator is running at what load efficiency

2 Answers  

how to calculate air load of a existing/ new plant before installing a air compressor.

0 Answers  

What is the different between brass and bronze ?

0 Answers  

why condensate pump can be used instead of feed pump?

1 Answers  

What is Governor A1 & A2 for engine

4 Answers   Nokia,

How tonnage can be controlled in PLC base hydraulic press

1 Answers