Answer / b0nz0

It will depend on the type of thermocouple and the
temperature of the reference (cold) junction.
If you measure 25degC in an ambiemt temp of 25degC you
should read 0mV.

Answer / carl_ellis

Question: What is output of Thermocouple at 25 deg C?

I'd flunk all of you except B0nz0 because only B0nz0
understands thermocouple thermometry.

The answer is, you don't know because the cold junction
temperature is not specified. The question attempts to
find out if the concepts of a thermal gradient and cold
junction compensation are understood. Which is why, I
assume, the question does not specify the type thermocouple.

B0nz0 is correct; any type thermocouple sitting on a desk
at 25 deg C; hot end = 25 Deg C, cold end = 25 Deg C, will
read 0.0mV because there is no thermal gradient.

The cold junction temperature is the same as the hot end
temperature. Doesn't matter if it's a Type K or J or S.
With the same temperature at both ends, the output is 0mV.

But without specifying what the cold end temperature is, an
answer of 0mV assumes that the cold end is at 25 Deg C.
In the real world, it usually isn't.

The hot end can be at 25 Deg C with the cold end on a
terminal strip in control panel that's at 45 Deg C because
of the heat generated by the electronics in the control
panel. Then you'll read a negative voltage because the
cold end is hotter than the hot end!

The hot end can be at 25 Deg C and the cold end is
connected to handheld temperature calibrator in northern
Canada in the winter where the cold end terminal connection
might be at -30 Deg C.

In each case, it's the cold junction compensation that
corrects the temperature reading by measuring the
temperature of the cold end connection and taking that
temperature into account.

If I were to ask the question, I'd ask, "What is the output
of a thermocouple, both ends of which are at 25 deg C, and
why?". The answer to the first part is 0mV.

Tell 'em Carl sent you.

Answer / mohammed abbas

Itis depend upon the sensitivity of the thermocouple used
because the different combination of alloy is having
diffrent sensitivity like.
1,copper/contantan =0.039mv/deg
25deg c=0.915
2,Iron/contantan=0.52mv/deg
25deg c=13mv
3,Platinum/rhodium=.05mv/deg
25deg c=1.25mv

Answer / mohamed yousuf

it is depend upon the sensitivity of the thermocouple used

Answer / srinath

one mv

Answer / shabbir ahmad

first of all see it type it depends on the type of
thermocouple for example s type thermocouple has 0.113mv at
20degc every type of thermocouple has different output at
25degc.

Answer / vishal

depends on the sensitivity...if ideal 298k

Answer / aditya

one millivolt

Answer / ishwar gurjar

1 mv for k type t/c .

Answer / harish

298 K

which gas or which liquid is filled in capillary of dial type temperature indicators on power transformers

2 Answers  

I want to measure and control level in tank of size 10*5 filled with gasoline, so plz give me the solution with clear details. how to select transmitter and sensors.

1 Answers  

How to measure high frequency using thermistor

1 Answers   DRDO,

hello this is dhinakar subramanian. how to piping and instrumenation drawings and also how to create the data sheets...

1 Answers  

i want to control the temp of sand(welding flux) between the range of 150deg C to 170deg C. sugges me sum temp control method without PID controller.

1 Answers  

what is Mv with respect to temprature in thermocouple

2 Answers  

difference b\w a transducer and a sensor

4 Answers  

WHAT IS THIS INSTRUMENTATION?

7 Answers  

Type of level transmitter commnly used in Procees area are the following. a.________________This type of level transmitter works as follows

1 Answers  

How a oxygen sensor & analyzer work at boiler or furnace, whats the principle & science is beyond this,How O2 sensor sence & convert signal & move toward analyzer & analyzer show reading in percent?

2 Answers  

Positioner usage.

1 Answers   CCIE,

what is the difference between(Flame proof/Explosion proof)& Fire proof instruments.Both are same or different & if different in which way because the transmitter which have approved ATEX flame proof enclouser but it use PTPE O ring & PTFE Head Gasket,so its (fire safe/fire proof)????????

4 Answers