Interested to Buy Any Domain ? << Click Here >> for more details...
What is A check, B check, C Check & D check for a diesel
Generator? Please guide me as this question was asked many
times and till now i haven't get right answer.If you can mail
me then please mail me the answer @ yogiagarwal@gmail.com.
- 20 Answers
- 522713 Views
- Apollo Power, BDV, Bosch, Further Future, Honda, HVCC, Jackson, Kirloskar, Multi Arc, Ranbaxy, Regulus IMC, TVS, XCD, YWS, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / amit kumar rathi
A-Check (Daily routein Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolent Level
8. Check Check V-Belt condition
B-Check (Every 300- 350 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
C-Check (Every 800-1500 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
6. Check All Electrical terminal & thimbles
7. Check polution level
D-check (Every 3000- 5000 Hrs.)
1. Complete DG set should be dismental.
2. Turbo charger service
3. Injector Pin service
4. Cylinder Head service
5. PT Pump sevice &
6. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozels,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check polution level
| Is This Answer Correct ? | 1622 Yes | 102 No |
A-Check
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolent Level
8. Check Check V-Belt condition
B-Check
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
| Is This Answer Correct ? | 825 Yes | 94 No |
Answer / anand
A check is daily check than B check is 6months or 350hourly
checking than C check is yearly 600 to 1200 hourely d check
is 1600 hourly
| Is This Answer Correct ? | 326 Yes | 77 No |
Answer / sanath shetty
A-Check (Daily routein Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolent Level
8. Check Check V-Belt condition
B-Check (Every 300- 350 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
C-Check (Every 800-1500 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
6. Check All Electrical terminal & thimbles
7. Check polution level
D-check (Every 3000- 5000 Hrs.)
1. Complete DG set should be dismental.
2. Turbo charger service
3. Injector Pin service
4. Cylinder Head service
5. PT Pump sevice &
6. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozels,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check polution level
| Is This Answer Correct ? | 248 Yes | 30 No |
Answer / lawrence p.c
A-Check (Daily routine Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolant Level
8. Check Radiator Fan Belt condition
B-Check (Every 300- 350 Hrs. or 6mth.)
1. Change oil.
2. Change oil filter, fuel filter, bypass filter & gas cut.
3. Change Air Filter.
4. Remove water from water Separator
5. Change gas cut for piston Head.
.
C-Check (Every1500 Hrs. or 1yr.)
1. Change oil.
2. Change oil filter, fuel filter, bypass filter & gas cut.
3. Change Air Filter.
4. Remove water from water Separator
5. Radiator cleaning with chemical
6. Check All Electrical terminal & thimbles
7. Check pollution level
8. Engine Injector setting
9. Change gas cut for piston Head.
D-check (Every 3000 Hrs or 2yr.)
1. Turbo charger service
2. Injector Pin service
3. Cylinder Head service
4. PT Pump service &
5. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozzles,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check pollution level
| Is This Answer Correct ? | 129 Yes | 19 No |
Answer / bhogesh biradar
DG A Check
this check is preventive maintainance of DG sets(1000-1500KVA).
1) A-check is done on daily basis here we check:
a) oil level
b) coolant level
c) gauge valve level
d) check for any leakage.
e) cleanliness of DG set.
2) B-check(done after 300hrs of cycle or 6 months whichever is earlier. )
a) check lube oil filter
b) fuel filter
c) air filter
d) bypass filter
3) C-check(done after 1500hrs of cycle or 3 yrs whichever is earlier.)
a) all steps of b-check.
b) check/change of air filter (if needed).
c) check/change of other filters mentioned in b-check.
d) change of gasket of chambers.
4) D-check
a) done in 6000 hrs of cycle.
| Is This Answer Correct ? | 101 Yes | 22 No |
Answer / shahsikant
In B check there is check only air filter not replacing
| Is This Answer Correct ? | 121 Yes | 70 No |
Answer / ranbir singh
what is d chek and what is part chage at the time of d chek.
| Is This Answer Correct ? | 60 Yes | 26 No |
Answer / deepak kumar
A check
Check lube oil
Check coolent level
Check drive belt
Check bettery terminal
All dg cleaness
All wire conection
All valve check
All motor check
| Is This Answer Correct ? | 40 Yes | 14 No |
What is the difference in specification of following pipe stand for 1 seamless pipe 200nb material SA355,P22,SCH80 AND 2 SEAMLESS PIPE 200NB,SA335,P11,SCH80
1. A single acting stage air compressor with 6% of clearance volume compresses air from 1.2 bar to 6.5 bar. Find the change in volumetric efficiency if the exponent of expansion process changes from 1.55 to 1.72.
What does CC Stand for?
Why rockets using liquid hydrogen have higher specific impulse compared to liquid hydrocarbon ?
The graphite in grey irons exists in the form of flakes which act as stress-raisers under tensile loading and consequently grey irons have relatively low tensile strength and ductility. Still grey iron is extensively used in engineering. Why ?
Name the safety devices of diesel engine?
hi friends, i want to know full depth of regarding mechanical seals
WHY ISOMETRIC VIEW LOOK LIKE 3D?
difference between load and force?
When effect of variations in specific heats is considered then how do maximum temperature and pressure vary compared to air standard cycle ?
• Explain about your dream job.
What is a torque converter?
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
