Interested to Buy Any Domain ? << Click Here >> for more details...
What is A check, B check, C Check & D check for a diesel
Generator? Please guide me as this question was asked many
times and till now i haven't get right answer.If you can mail
me then please mail me the answer @ yogiagarwal@gmail.com.
- 20 Answers
- 524938 Views
- Apollo Power, BDV, Bosch, Further Future, Honda, HVCC, Jackson, Kirloskar, Multi Arc, Ranbaxy, Regulus IMC, TVS, XCD, YWS, I also Faced
- E-Mail Answers
Answer Posted / lawrence p.c
A-Check (Daily routine Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolant Level
8. Check Radiator Fan Belt condition
B-Check (Every 300- 350 Hrs. or 6mth.)
1. Change oil.
2. Change oil filter, fuel filter, bypass filter & gas cut.
3. Change Air Filter.
4. Remove water from water Separator
5. Change gas cut for piston Head.
.
C-Check (Every1500 Hrs. or 1yr.)
1. Change oil.
2. Change oil filter, fuel filter, bypass filter & gas cut.
3. Change Air Filter.
4. Remove water from water Separator
5. Radiator cleaning with chemical
6. Check All Electrical terminal & thimbles
7. Check pollution level
8. Engine Injector setting
9. Change gas cut for piston Head.
D-check (Every 3000 Hrs or 2yr.)
1. Turbo charger service
2. Injector Pin service
3. Cylinder Head service
4. PT Pump service &
5. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozzles,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check pollution level
| Is This Answer Correct ? | 129 Yes | 19 No |
Post New Answer View All Answers
Why is heat treatment required?
my dad is refused 8 times in visitor visa? now my dad wants to go usa only? tell me what he can do? whats the reason?
What are the minerals needed to make or build a car?
Explain the term torque
Causes of M/E high exhaust valve temperature
What are the purposes of spiral gear in a purifier?
What is turbocharger and his rpm
Why centrifugal pump is not called as a positive displacement type of pump?
If gas turbine is operating on part load, how droop will affect the output with respect to frequency.
"When you will install a new piston ring, what will be the position of it?"
Which parameter remains constant in isochoric process ?
Name the four most important components of a Freon refrigeration system.
HOW LIGHTENING PROTECTION IS DONE ON ROOF OF SQUARE SHAPE AND HAVE PARTUCULARLY BIG SURFACE AREA.
How to calculate motor bearing life - cycle (life time) (SKF bearing)
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
