1) what is the use of pin and plate vibrators during slab
casting? 2) how much cement bags are required for 1sqm
4inch brick wall? 3) Is it viable to provide overlap at
column , beam & slab junction. if no why? 4) if bar dia is
changing in column reinforcement , which dia bars overlap
is considered? 5) what is isolated and ecentric footing?
Answers were Sorted based on User's Feedback
Answer / sk
1.vibrators are used to compact the concrete placed to make
it homogenous mass removing air voids present in it.2.0.2
bags per sq.m 3.no.because it falls in critical zone
4.higher dia bar dia considered 5.isolated footing is a
footing having single column and cg of column and footing
pass from same point.
| Is This Answer Correct ? | 9 Yes | 3 No |
Answer / kamlesh chauhan
(1)pin or needle vibrattor is used for beams,columns and
slab bottom for vibration of concrete,while plate vibrators
are used on surface to compact the conc in layers.(2)cement
consumption is 0.12 bags.(3)question is not cleared(4)bars
are laps as per lower level for which casting of columns
are over.
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / kartik khanna
vertically no. of bricks used of dimensins 19*9*9cm along
with a key mortar dimension of 10mm with each brisk is 10
slly horizontally the no of bricks used will be 10
length of cement used will be 10cm vertically and 8cm
horizontally
so area of cement used is 80 cm^2
1m^2=28.8 bags of cement
.8 *10^-2 m^2=.2304 bags of cement
but if we take mortar of 1:3 ratio instead of cement then
the cement used will be .2304\3=.0768bags of cement
| Is This Answer Correct ? | 4 Yes | 1 No |
Answer / modipraveen
Hi, I am answering a answer for each question.
Pin/ Needle vibrator are to remove air/void in concrete
generally its used for deep thing like Beam, columns and flat
slab and even slab where heavy reinforcement is used.
Plate vibrator are used to have rigid base like grade slab,
RCC/CC roads.
| Is This Answer Correct ? | 3 Yes | 1 No |
beam top main reinforcement(25mm) was drilled off by mistakely when making drill hole for dummy columns. any one can give useful information for this issue or related code or websites.
what is the formular for measuring minimum depth of a foundation
what is poissons ration of steel?
115mm thickness brick work how to required mortar
How find out Rolling margin of steel dia.wise?
what is the code provision for acceptance of fineness modulus range for fine aggregates in design mix
How reactor of SBR installed , is it be over ground, fully under ground or semi sunk ?
what is the quantity of concrete required in 1 cubic meter volume without reinforcement
Which of the following armed forces has decided ( in August 2016) to appoint P V Sindhu ( Olympic silver medalist) as its brand ambassador? A) ITBP B) CRPF C) NSG D) CISF
How many kilograms of sand required in cufic feet for one cubic meter of M25 grade concrete
what is meaning of inverted beam.is it way to provide double mat in slab one at bottom and another at topif we go for provision of inverted beam. shall we construct structure with out plinth beam for us we have to construct small bus shelter
0 Answers Anish Constructions, STUP Consultants Pvt Ltd,
what is the density of steel
10 Answers NGO, PWD, Sepco,
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)