Answer / jadish arya

silt should be 5%

Answer / saddam hussain

silt content % limit where it mentioned in is-383 code

Answer / sanjeev

IS 383 gives limit for 'material finer than 75 micron' as 3% for uncrushed and 15% for crushed fine aggregate, and this is for a combination of silt (0.002 to 0.075 mm) and clay (<0.002mm), and not only for silt.

Answer / siddharam g

I need suitability of silt content in construction work

Answer / vishal bhart kunturkar

8% but according to zones variation it also varries

Answer / sagar sawant

Silt content shoud not be more than 5% of sample of sand
Volume

Answer / v.kapil

As per IS 2116 it should not be more then 5%.

Answer / vasanth kumar

Only 6% of silt

Answer / gokul.m

should not be more than 6%

Answer / guddu singh

It's must that silt %
between 0-6% as per
IS If silt is more than
6% then we are
cleaning sand......

what is meant by csr in foundation? what is sbc?what is meant by contour line?

0 Answers  

What is the Maximum & Minimum size of rod using on the column?

5 Answers  

How many pyramid in egypt?

0 Answers  

How many square meter can mason layout chb per hour

0 Answers  

I am planning to construction in my plot in Pune (Chandan Nagar) and its near about 1950 SqFt. Can some plz help me on the rate on per sqft for RCC,Brickwork & Plaster,Flooring,Water proofing,Door. Thank you in advance

1 Answers  

Please tell me about surveying standard chain details.Thanks.

1 Answers  

pls mail some more tecnical qustions at msaranya2610@gmail.com

0 Answers  

Q1) I am having an interview in a construction company for a large sewage project . Since I have not done any such project , there are some queries from my end. Pls. help me to solve them. I will be thankful to you :- a) Normally for large project 400-600 houses & around 1600 peoples , how much dia pipe is used and which type of pipe is used? b) For trenching , I have heard that IS 1200 implies, what are the rules of calculating earthwork in case of depth of 2m or above ? c) To prevent soil to fall when depth of trench is more , what steps are taken and how there qty. is calculated . Like I have heard about timbering . what is this ? d) What are the rules for disposing off the excavated soil ? e) How the pipes that are used are being jointed? f) In case of cleaning on choks , is there any intermediate things provided? g) For foul gases any outlets are provided thru out length of pipeline? h) What is the flow digram like from houses thru small pipe to main pipeline than where main pipeline disposes wastage ? i) Any other thing that has to be kept in mind while calculating earth work for excavation like steps are made and other things? How earthwork is calculated in case of steps ? Pls. explain with a sketch. Regards,

1 Answers  

1:6 mortar, how many self life hours ?

4 Answers   CCCL, L&T,

for solid cement brick without fly ash,we use dust,6mm,12 mm jelly,water my question is what Proportion we mix dust,6mm,12 mm jelly,water ? for good strength brick.

1 Answers   bsmcpl, Ramky,

I want to know about rolling margin of steel :- For eg. If 2nos. bundle of 8mm dia steel with17 rods each of length 12m comes to store. During testing of 1m rod of each bundle it was found that 1rod has weight .405kg/m while other has .385kg/m. Now what will happen in case of steel payment and measurement payment ? Regards,

0 Answers  

technical name of shuttering plywood

1 Answers