Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


i have dry type transformers can you help me that how many
tests i can do to know the performence of transformer and
also please tell me about the BDV test and Insulation
resistance test in oil cooled transformers

Answers were Sorted based on User's Feedback



i have dry type transformers can you help me that how many tests i can do to know the performence ..

Answer / s ghosh thakur

The following tests to be done during commissioning.
1.Duster value.
2.PI test The value should be above2.o
3.Tan delta test.
4.Ratio test.
5.short ckt.impedance test.
6.vector test.
7.IR test.
8.Polarity test. Thats are sufficient.

BDV value of TRANS OIL should not be less than 50 kv.
IR value of oil cooled trans should be 100M w.r.t gr.and HT
to LT also 100M.PI test should carried out value min 1.5 to
2.0

Is This Answer Correct ?    2 Yes 1 No

i have dry type transformers can you help me that how many tests i can do to know the performence ..

Answer / brijesh soni

yes this ans is right you may be test Oppen circuit test,
Megnetic bellence test And very important Inples test.

Is This Answer Correct ?    0 Yes 0 No

i have dry type transformers can you help me that how many tests i can do to know the performence ..

Answer / nithiya

tan dalta test only for above 220KV higher rating
transformers only conducted , Impuls test only conduted in
factory only..and Asper IS 1866-2000 less then 72KV=40KV,
170KV=50KV above 170KV=60KV.

Is This Answer Correct ?    0 Yes 0 No

i have dry type transformers can you help me that how many tests i can do to know the performence ..

Answer / pinaki chatterjee

according to all routine test as per IS-2026 PART 1 and magnetic balance, also current balance test should be require if necessary temperature rise test can be made.

if the voltage level is 11 kv so IMPULSE TEST AS PER clause 12 can be made for better acivement.

partial discharge should always check

Is This Answer Correct ?    0 Yes 0 No

Post New Answer



More Electrical Engineering Interview Questions

Hi all, please could anybody give me a suggestion about Electrical designs and calculations .. what text book should i follow as i am a trainee engineer and here work going not so favorable to me so please help me friends .. A small discription about my work which is going here is all about Electrical designs like cable sizing, lighting, lightning, Gensets sizing, motor sizing, transformer sizing, generator sizing, circuit breakers, PDB MCC PCC SLDB MLDB panels, Single line diagrams mainly, substation desings, cable routing and layouts, reactive power compensations, power factor improvement, voltage drop calculations, power generations, power transmission, power distributions all calculations i need .. please please if anybody experienced with this problem and got a solution then please help me .. just i need an apt text book for these all calculations and designs ..

0 Answers  


Why generally the Rating of Transformers are in additions of 11 i.e. 11 kVA, 22 kVa, 33 kVA, etc........

8 Answers  


why do we use 25kv supply for traction purpose

1 Answers  


We have a couple of oil tanks at our plant. One of them does not have a lightning arrester installed. My question is it necessary to install an arrestor on every tank or will this particular one be covered by the arrestor installed on the ajdacent tank, Since all the tanks are close to each other. Basically, I want to know that if these arrestors or protection works in a parituclar area of effect or influence. Thanks

0 Answers  


what is a breaker fail relay

0 Answers   Eskom,






a voltmeter shows 100v..wat is to be done to make it read 150v.

7 Answers  


What current flows in the transformer primary when its secondary is open?

0 Answers  


How is the air circuit breaker quenching the arc. If it is by air means, where is it come from?

1 Answers  


how to select automotive wire by mathematical equation with given current, vlotage and resistance

0 Answers   Tyco,


Sir, I have applied for the of Jr.engineer(Electrical & Electronics) & ASST. LOCO PILOT at ALL RRB BOARDS. please send me all RRB Boards solved papers in the year of 2001 tO till date. i requested send me the papers to my id as soon as possible (jet_0991@yahoo.com). (This is very urgent) Thank You,

0 Answers  


What is the meaning of HT Trivector Meter ?

0 Answers   NIIT, Sodexo,


Why PT burnts?

2 Answers  






Categories
  • Civil Engineering Interview Questions Civil Engineering (5076)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4445)
  • Electrical Engineering Interview Questions Electrical Engineering (16606)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2992)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1378)