Answer / prabhakaran

DC transformer is not possible.according to transformers
mutual induction principle,which can possible only on
alternating current (AC).

Answer / uttam kumar sarkar

It's Impossible, because DC cannot produce Mutual Flux.

Answer / nandhakumar

not possible

Answer / suresh kumar k

The question itself is a little wrong, infact the question
should be "Why we will not apply DC to a Transformer, if it
applies what happens?

The answer is, there is no inductance effect produced in DC
as such in AC. If we apply a DC voltage to the primary of
the winding then there will be no Back EMF produced in the
primary winding because of lack of self inductance in the
winding for DC. Hence huge currents of the order of
thosands of Amps flow in the Pri. winding and leads to fire
in the winding. Also Since there is no mutual inductance
effect in secondary of the winding there will be no induced
EMF in secondary.

Answer / mahesh

DC transformer is not possible because a Xmer work at
principle of electromagnetic induction i.e. to say they work
at rate of change of flux & mutual induction & this is not
possible in DC so Xmer work only in AC

Answer / animesh verma

DC transformer is possiblle...
Its a well known topic of HVDC area..
See any HVDC book and look for DC current transformer it is
used to sense the current in HVDC links it has got two
rings over a straight rod and has got some AC bias...

Answer / kakanivenkatesh

transformer works in mutual inductance principle ..mutual
inductance is possible only for ac..

Answer / ashish verma

no it is not possible bcz there is constant flux

Answer / naresh

it is possible for small applications.the ransformer will
work for small period of time for given DC input as it will
produce little amount of flux for some time, but not
constant.as the flux is not constant, we prefer AC
transformer.

Why D.C Voltage used in Meggering...as well as in Hipot test? why not A.C?

2 Answers  

WHY NOT CONSIDER PROTONS IN ELECTRICITY LIKE ELECTRIC CURRENT?

1 Answers  

can anyone give an idea about dia calculation in cold rolling mill

0 Answers  

circuit diagram of trip circuit supervision relay

0 Answers  

what is protection class current transformer.

1 Answers   Matrix,

I am an electrical contractor in noida, I am registereg in noida vat. i got a contract in Delhi State, my party told me that we shall deduct WCT @4% & reimburse Service tax all in composite scheme. Now Problem is this, 1 Can i able to purchase outside the delhi? 2 Can i produce a c form to our vendors? 3 What is limitation of purchase from outside the Delhi? 4 What % of tax Govt will levied upon me? 5 How can i take credit of tax paid upon purchase made by us. So, like these type questions i have in my mind if any person know the right answer please write to sksproj@gmail.com or contact me on - 8010076534 / 9212758177 / 9718378190. Thanks with Best Regards, S.K.Saxena

3 Answers  

What is ignition module of a CAT Gas Genset G-3508 Engine, Alternator SR4B Series. HOw its checked for correct functioning.Is it repiarable or replacable?

0 Answers  

What are the effects to a distribution transformer rated 10Kv with ratio 10Kv/0.433Kv, 3phase 50hz for example but fed with power supply of 11Kv?

2 Answers  

how to calculation increase power factor for single phase

0 Answers  

what is the excess air in furnace

0 Answers  

Draw a 230kv two-bus bar system showing the following. 1.Two generators (150MW) each connected through one 15.75/230KV transformers 2. 1 outgoing lines 3. Two 230/130 KV transformers 4. BUS PT's 5. CT

0 Answers  

Two CTs 1600/1 and 35/1 are in series. while checking the ratio test of a CT(1600/1),same 1600A will also pass through the CT having ratio 35/1. Will it be harmfull to the ct(35/1),if yes , what will happen.CT secondary is shorted

3 Answers