what should be the megger test report for 11KV cable when meggered with 5KV me

Categories >> Engineering >> Electrical Engineering
Suggest New Category

what should be the megger test report for 11KV cable when
meggered with 5KV megger , what is the resistance value we
should get

Question Posted / guest

7 Answers
14798 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / ajit

>10000 megaohms

Is This Answer Correct ?

15 Yes

2 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / ahmed

>11 G ohms

Is This Answer Correct ?

3 Yes

0 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / jesudoss

for land minimum >50 mega ohm, marine >100megaohm.its
minimum requirement . but this value can be vary depends
upon the surveyor like DNV,BV,ABS,LOYDS etc.

Is This Answer Correct ?

1 Yes

0 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / chamara

>1000Mohm

Is This Answer Correct ?

2 Yes

3 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / bhigesh

2.2

Is This Answer Correct ?

6 Yes

8 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / engr syed wajahat hussain

it should be exactly more than 12 Mega ohm

Is This Answer Correct ?

3 Yes

5 No

what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the r..

Answer / velusamy

min of 11 megohms

Is This Answer Correct ?

5 Yes

10 No

Post New Answer

More Electrical Engineering Interview Questions

if in 3-phase system voltage=440V,frequency=60Hz, current=400A. then if it is single phase then current=? and if it is single phasing then current=?

0 Answers

How to reduce the static electricity producing in solvent room? By P.D.Patil BioCon

0 Answers Biocon,

An input device is interfaced with Intel 8085A microprocessor as memory mapped I/O.The address of the device is 2500H.In order to input data from the device to accumulator,the sequence of instruction will be

1 Answers GATE,

What is derating?, Why it is necessary, it is same for all means for drives, motors,and cables.

1 Answers

Where is 2 phase supply used commercially?

3 Answers NTPC,

How harmonic block test are conducted on relays ( Siemens,Areva ect )power transformer using omicron kit?

0 Answers Siemens,

I am having a 1500 KVA transformer whose secondary current is 2086A and my connected load is 1000 KVA, I am having 400 KVAR APFCR for PF improvement what ratio of CT should i install in LT EB Bus to get optimum PF improvement?

0 Answers

10 hp motor ,7.5 kw ,960 rpm, full load current 15.5, delta connection so how much take current no load trial time. any formula please give..... second question :- what is different between brekar control wiring and motor starter control wiring

1 Answers MSP,

give me applications of sequence bridges . (used in 3 phase un balanced systems)

0 Answers

What are the function of different components of servo motor?

0 Answers BARC, Parle,

why we use MV panels??? what's r all the needs

4 Answers

HOW TO CALCULATE ELECTRICAL, MECHANICAL,& OVERALL EFICIENCY OF GAS ENGINE POWER PLANT

0 Answers

For more Electrical Engineering Interview Questions Click Here