Slip joints are provided in the propeller shaft a) To adjust the inclination of the propeller shaft b) To adjust the length of the propeller shaft c) To prevent the whirling of the propeller shaft d) To adjust the up and down movement of the rear axle
891If two shafts used for transfer of drive are inclined to each other, then a) Slip joint is used b) Flange coupling is used c) Universal joint is used d) None of the above
869The Hook's joint works efficiently when the propeller shaft inclination is a) 18o b) 28o c) 38o d) 48o
887The function of the final drive is to a) Provide a permanent speed reduction b) To turn the drive round through 90o c) To provide drive to the rear wheels d) all of the above
1003The permanent reduction provided by the final drive in heavy vehicle is a) 4:1 b) 6:1 c) 8:1 d) 10:1
879The function of Differential is a) To prevent wheel skidding b) To reduce the speed of the inner wheels during turning c) To keep the speed of all the wheels same when going straight ahead d) all of the above
991The crown wheel of the final drive is connected to a) Cage b) Spider c) Cross pin d) Axle half shaft
971In a vehicle, which is going straight ahead at N rpm, if the left wheel rotates forward at n rpm, then the resultant speed of the right wheel will be a) N+n b) N-n c) N/n d) Nn
963I have purchased some circlips @rs 100/- p pc on 01.01.2017 ans some @rs.120/- p pc/@rs.90/- p pc dt. 31.03.2017 what is the ending price of per pcs
935ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.19 : In the purchase of a unit of engineering office, a loan has been made to a bank with the following details : Term N = 30 years; interest rate R = 8.07 % / year; security : primary residence; present value pv = $450000; salary = $75000 / year or $56000 / year after tax. (a) Let the discounted present value PV = [ 1 - 1 / (1 + r) ^ n ] / r for arrears, where r = interest rate of discount, n = number of payment, ^ = symbol for power. If the loan repayment was made monthly : (i) calculate the value of r where r = R / k and R is in decimal value; (ii) find the value of n where n = kN; (iii) estimate the value of k where k = number of repayment per year; (iv) calculate the value of PV based on the formula of discounted present value. (b) Calculate the monthly repayment of the loan, MR based on the following formula : pv = PV x MR. (c) Find the percentage of salary remains after paying the loan every month.
1 1444Please tell me any one, how many quantity concrete paver block fixing perday ( 8hours) per mason??
NCC,
1161
1.main parts of generator? what is used A-check,B-check,C- check? 2.what is FM200 system in data centers? 3.difference between pac,ahu?
SUTIABLE FOR ohm's law super conductor
Why is 400 hz used for flight instruments and radio transmission system in aviation industry universally?
How does a tank-blanketing valve operate?
What is the advantage of using ayrton or universal shunt in multi-range ammeters?
How many types oil using in transformer ? How many letars using in transformer..?
when reinforcement binding completed if there is more cover than the required what is the solution to reduce the cover?
what is a bus riser in power system and why it is used
Is there a diode made that works with AC 120 volt 20 amp? If so can it completely stop all current flow in 1 direction at all times?
What is the effect of addition of zinc in copper? What is the use of 70/30 brass ?
Share with us about a time when you had to present a proposal to a person of higher position and were able to do it successfully?
There are a trformer and an induction machine. Those two have the same supply. For which device the load current will be maximum? And why?
Discuss how to prepare the M/E in the standby condition
Name any four accessories?
What are encoders and decoders?