The point of interaction of the tractive effort curve and the total resistance curve is called a) Stabilizing speed point b) Low speed point c) High speed point d) Normal speed point

Backbone, Bosch, MAHINDRA, Uniparts Group,

If the given tractive effort curve and the total resistance curve does not intersect, then a) The vehicle will accelerate b) The vehicle will decelerate c) The vehicle will not be able to go at this gradient for the given gear d) None of the above

Backbone, Bosch, MAHINDRA, Uniparts Group,

The main disadvantage of sliding mesh type of gear box is a) High noise level b) Low mechanical efficiency c) High skill required by the driver d) all of the above

Backbone, Bosch, MAHINDRA, Uniparts Group,

Double declutching is used for the engagement of gears in a) Sliding mesh type of gear box b) Constant mesh type of gear box c) Synchromesh type of gear box d) None of the above

Backbone, Bosch, MAHINDRA, Uniparts Group,

High speed gear is obtained in the case of sliding mesh gear box when a) Motion is transferred through the clutch gear to lay shaft gear b) Main shaft is coupled to the clutch shaft c) Smallest gear on the lay shaft is engaged d) Largest gear on the lay shaft is engaged

Backbone, Bosch, MAHINDRA, Uniparts Group,

The Figure 1 depicts a) Top gear b) Second gear c) First gear d) Reverse gear

Backbone, Bosch, MAHINDRA, Uniparts Group,

In case of a constant mesh gear box, when the left dog clutch is slid to the left by means of the selector mechanism, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained

Backbone, Bosch, MAHINDRA, Uniparts Group,

In a constant mesh gear box, when the right dog clutch is engaged with the gear on the right side of the main shaft, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained

Backbone, Bosch, MAHINDRA, Uniparts Group,

Double declutching is required in constant mesh gear box a) To equalize the speed of main shaft gear and the sliding dog b) To provide direct gear c) To equalize the speed of countershaft gear and the sliding dog d) None of the above

Backbone, Bosch, MAHINDRA, Uniparts Group,

The number of spring loaded balls provided circumferentially in a synchromesh gear box is a) 3 b) 4 c) 5 d) 6

Backbone, Bosch, MAHINDRA, Uniparts Group,

In a synchromesh device, when members G1 and F1 are slid to left and cones M1 and M2 are in contact, a) Direct gear is obtained b) Second gear is obtained c) Third gear is obtained d) Reverse gear is obtained

Backbone, Bosch, MAHINDRA, Uniparts Group,

For the second gear in a synchromesh system, the drive transfer will be through a) U1, U2, C, F2, and splines b) U1, U2, C, F1, and splines c) U1, U3, D, F3, and splines d) U1, U4, U5, E, F2, and splines

Backbone, Bosch, MAHINDRA, Uniparts Group,

Interlocking mechanism is provided in the gear box cover a) To prevent engagement of two gears simultaneously b) To prevent engagement of reverse gear c) To facilitate the gear selection d) To avoid the necessity of having neutral gear

Backbone, Bosch, MAHINDRA, Uniparts Group,

Stiff spring is used in the selector mechanism a) To prevent engagement of two gears simultaneously b) To prevent engagement of reverse gear c) To facilitate the gear selection d) To avoid the necessity of having neutral gear

Backbone, Bosch, MAHINDRA, Uniparts Group,

Propeller shaft is used for the purpose of a) Transmitting the drive from the transmission to the bevel pinion of the final drive b) Transmitting the drive from the crankshaft to the road wheels c) Transmitting the drive from the transmission to the road wheels d) Transmitting the drive from the crankshaft to the bevel pinion of the final drive

Backbone, Bosch, MAHINDRA, Uniparts Group,