Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
What is the effect on Power factor and capacitor when your company load is more than 70 % of welding transformer
1775How to protect a Dosing pumps/any sensitive equipment (single phase) from surge protection inside a food factory.
1688How to protect sensitive loads such as Dosing pumps inside a factory from voltage surge/voltage fluctuation.
1767Multi-step core is used in transformer to: A) Increase the output B) Decrease the cost of core material C) Decrease the cost of copper D) Increase the efficiency
1 9102DIRECTIONS for questions 8 and 9: Refer to the data below and answer the questions that follow. There are seven chapters in a mathematics book - A, B, C, D, E, F, and G. The instructor has to follow certain rules while teaching them. i. E cannot be taught before B and C. ii. D should be taught before C and G. iii. B cannot be taught before G. iv. F cannot be taught before C, D, and G. v. A should be taught before B is taught and the two should not be taught consecutively. Q8. If only four chapters are taught, which of the following has to be necessarily false? a) The instructor can get away without teaching F. b) The instructor can avoid teaching E. c) The instructor can avoid teaching C. d) The instructor can avoid teaching G. Q9. If only four chapters are to be taught, which of the following is necessarily true? a) A has to be taught. b) D has to be taught. c) B has to be taught. d) C has to be taught. Q8. If only four chapters are taught, which of the following has to be necessarily false? a) The instructor can get away without teaching F. b) The instructor can avoid teaching E. c) The instructor can avoid teaching C. d) The instructor can avoid teaching G. Q9. If only four chapters are to be taught, which of the following is necessarily true? a) A has to be taught. b) D has to be taught. c) B has to be taught. d) C has to be taught.
1 3953Does outdoor isolator loose connection cause short circuit current in that circuit? if yes then how ??
1669Hallow everybody, we want to know in a NPk fertilizer process plant (Bulk Blender) we are in doubt if use square or rectangular hopper jus to avoid the vault effect durin the flow of of raw material like Phosphorus, Potasium and zeolite..Please any advise will be appresated Isdray
4240i have a 4 Mva transformer 34.5 kv / 480-277 v and i used 2 parallel 3200 amp bus duct for the secondary feeder using 3 ply of bus bar ( 3/8" x 5" ) as a common where the flexible link terminated and 6300 amps breaker for the main, the lower bus duct reaches 70 degrees and the upper bus duct reaches 55 degrees when i used thermal scanner. why the temperature is not balance when the load reaches 3600 amps.
SCM,
1878I am applied 100 % pressure on to the air to open control valve,but the valve is not fully closed..and 10-15% is open the valve. how to calibrate the control valve?
OPaL,
3 4195
composition of cast iron fc-500,fc-550,& fc-260 which is use in sheet metal industries as a piller set
how u calibrate sox nox co2 co in cemps?what is opacity n HPm?tell the standard parameters of cems?
what is transmission ?how transmission is done in nokia 3G?
if any body have tyco electronics placement papers,please forward to my mail id kadhar.basha@gmail.com ,please as early as possible. thanks®ards kadhar basha
How can I calculate per unit (KWH) fuel (Gas/ Diesel both) consumption 1MW unit?
List the disadvantages of constant k filters?
What is a sample and hold circuit? Where it is used?
pls give me ans to ACT formula cube testing porpuse
what is the maximum permissible limit value of leakage current and leakage counter reading to replace lightining arrester?
What is the perfect face shape? Why it is called so?
why booster transformer is used in sumpners test conducted on transformer????
Explain the use of excitation table in digital electronics?
what r the checklist while installing a 380 kva DG set
what can passengers do to ensure safety?
how to identify the failure of building by expansive soils
