for testing busbar (33kv) hi-pot .whether we can apply DC r not.and what is th

for testing busbar (33kv) hi-pot .whether we can apply DC r
not.and what is the test volt for that .explain

Question Posted / sanjeevi

4 Answers
15557 Views
WGPSN, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

for testing busbar (33kv) hi-pot .whether we can apply DC r not.and what is the test volt for that..

Answer / senthil kumar

we can able to test ac or dc. thats manufactures chosen.in ac hi-pot leakage current will be more(mA).but DC hi-pot leakage current will be less. but dc voltage charge the capacitance. in ac hi-pot we are applying 2V+1X 0.8 in dc hi-pot 2V+1X1.414X 0.8.

Is This Answer Correct ?

11 Yes

1 No

for testing busbar (33kv) hi-pot .whether we can apply DC r not.and what is the test volt for that..

Answer / vijay

Yes, we can.
For test voltage we have to apply 80% of factory test
voltage i.e. 80% of 70 kv ac (factory test voltage) =56 kv
for 1 min.

Is This Answer Correct ?

11 Yes

6 No

for testing busbar (33kv) hi-pot .whether we can apply DC r not.and what is the test volt for that..

Answer / shaikh

For 33KV Ac Busbar testing, we can apply 5.0k (5000v)DC for
1-3 mints.

Is This Answer Correct ?

3 Yes

10 No

for testing busbar (33kv) hi-pot .whether we can apply DC r not.and what is the test volt for that..

Answer / ashish

For Testing Busbar 33 Kv ( HI-POT ) We Have To Apply the (
1.732* 33000)DC Volt for 3 min.

Is This Answer Correct ?

9 Yes

18 No

Post New Answer

More Electrical Engineering Interview Questions

what is transformer

63 Answers ABB, Advance Power Controls, CERC, Electrical, Electrical Supervisor Competency Certificate, ETA, IBM, Jindal,

What are the components of a substation?

3 Answers IOCL,

Why dc Supply used in Control circuit.

12 Answers HP,

solor panels arrange some angle,panel is flat fitted energy was produced or not why?

0 Answers

What is the Difference Between the SCADA & PLC ? Both it also control and Supervise Then what Special in Scada & PLC?

1 Answers

Describe the method of Plate Earthing.

1 Answers

State the formula for overall efficiency of thermal power station

0 Answers

y r manufacturing fan is running into clockwise direction?y they can made in anticlock direction?pls give rply/ venkat.gattupalli@gmail.com pls send to my mail....

1 Answers

If i switch on a transformer but with no load connected to the secondary path.Is the transformer will burn?

5 Answers

(1)The demand for electricity , the amount of renewable generation available, the amount of fossil fuel generation available and the cost of the fossil fuel generation are shown in table below period(hrs) demand(MW) renewable (MW) fossil- fuel(MW) cost of fossil fuel(MW) 00.00 - 01.00 2000 1800 2000 30 01.00 - 02.00 2300 2500 2000 30 02.00 - 03.00 2500 2700 2100 45 03.00 - 04.00 2900 3100 2100 50 04.00 - 05.00 2700 2600 2500 45 05.00 - 06.00 2400 2000 2700 50 06.00 - 07.00 2200 1800 2000 36 07.00 - 08.00 2100 1600 2000 36 Assuming that the renewable generation incurs zero cost, determine an optimal generation schedule(specifying the amount of renewable generation and fossil fuel generation used in each period, the cost for each period and the overall cost for 8 hours.)

0 Answers

How silicon gel sucks moisture in the transformer, its have any small exaust fan behind silicon gel.

4 Answers

I have an 15A fuse MCB that controls a night storage heater. It needs replacing and is now obsolete. Is a 16A C curve MCB the correct replacement?

2 Answers

For more Electrical Engineering Interview Questions Click Here